If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Has Anyone installed a VDO Electric Speedometer?
AS luck would have it I replaced the mechanical old VDO speedometer in my dune buggy with the newer electronic version. After calibrating the thing on a true mile distance and getting it to work, the needle movement is worse than the damn gas gauge splashing around. Way to much lag and jump in the way this works. Does anyone have such a beast installed, and if so does it give accurate smooth speed readings. Scott 69' Dune Buggy |
Ads |
#2
|
|||
|
|||
Scott wrote:
> AS luck would have it I replaced the mechanical old VDO speedometer in > my dune buggy with the newer electronic version. After calibrating the > thing on a true mile distance and getting it to work, the needle > movement is worse than the damn gas gauge splashing around. Way to > much lag and jump in the way this works. Does anyone have such a beast > installed, and if so does it give accurate smooth speed readings. > Scott > 69' Dune Buggy > No, I haven't used that one. But did you see the post recently (who was it?) about putting a digital speedo in a buggy? The ones used on bicycles are going for $10-20. Speedy Jim http://www.nls.net/mp/volks/ |
#3
|
|||
|
|||
The second part of this is my dash board has 5 vdo royal cockpit gages
installed on a nice chrome panel. This was the previous owners show car. So, not wanting my buggy to look like a mexican chevy monte carlo (I live in texas you see) I replaced the old true mechanical one with this new "MORE ACCURATE" one. The old one was around 5MPH off (according to radar) and I've snapped 2 cables already because of the very tight bend as it comes out of the gage and meets the underside metal cross member behind the dash. Typical, swap one problem for a different one. |
#4
|
|||
|
|||
Scott wrote:
> The second part of this is my dash board has 5 vdo royal cockpit gages > installed on a nice chrome panel. This was the previous owners show > car. So, not wanting my buggy to look like a mexican chevy monte carlo > (I live in texas you see) I replaced the old true mechanical one with > this new "MORE ACCURATE" one. > The old one was around 5MPH off (according to radar) and I've snapped 2 > cables already because of the very tight bend as it comes out of the > gage and meets the underside metal cross member behind the dash. > Typical, swap one problem for a different one. > LOL I hear you. Then I guess it's time to re-engineer the VDO design or maybe write/call them. http://www.vdona.com/Tech%20Support/...tionsheets.htm http://www.vdona.com/aftermarket/aftermarket.html If they are no help, I'm thinking big capacitor across the meter to damp the oscillation. Does it use a single magnet to trigger from a wheel? (maybe an additional magnet with suitable recalibration. Hard to imagine that VDO hasn't run into this complaint. Speedy Jim http://www.nls.net/mp/volks/ |
#5
|
|||
|
|||
Thanks...
This gage as mentioned works from the standard VW cable that mechanically runs through the front left spindle and attached to the dust bearing cover cap. So as the wheel spins so does the cable....and the other end of the cable screws into this "hall effect" sensor unit....from the sensor unit, 3 wires then attach to the gage...the gage has a few more wire attached for ground, panel light, and ignition switch. Pretty simple, very easy to wire. Also, is 2" thick so you just can't attach something across the meter terminals in back. This is a "smart" gage, you program the # of counts in a "mile". Has other features also, but no "damping effect". Naturally I've been to VDO's web page and as normal nothing there to help. Even their email for tech support bounced back....and this the weekend now any help from them will be Monday. As expensive as this gage is, it should work perfectly without having to tweak anything. |
#6
|
|||
|
|||
Scott wrote:
<SNIP> As expensive as this gage is, it should work > perfectly without having to tweak anything. > Hard to argue with that:-) Thanks for clarifying the other points; this is another beast I haven't encountered yet. Let us know if/when you get a satisfactory answer from VDO. Jim |
#7
|
|||
|
|||
>This gage as mentioned works from the standard VW cable that >mechanically runs through the front left spindle and attached to the >dust bearing cover cap. So as the wheel spins so does the cable....and >the other end of the cable screws into this "hall effect" sensor >unit....from the sensor unit, 3 wires then attach to the gage...the >gage has a few more wire attached for ground, panel light, and ignition >switch. Pretty simple, very easy to wire. Also, is 2" thick so you >just can't attach something across the meter terminals in back. This >is a "smart" gage, you program the # of counts in a "mile". Has other >features also, but no "damping effect". Naturally I've been to VDO's >web page and as normal nothing there to help. Even their email for >tech support bounced back....and this the weekend now any help from >them will be Monday. As expensive as this gage is, it should work >perfectly without having to tweak anything. Scott, Sound to me like the cable is either loose (or lose if you don't care how to spell it) or the hall effect sensor is no good. I'd definitely be more likely to suspect something in the installation than the product, from my experience with the VDO products. Start by checking the end of the cable is secured to the hub center cap. then make sure the cable is not dry or lubrication is too thick to allow smoothe operation ( or is it Smooth??? or Smothe? LOL ) Anyway, try and make sure there is absolutely nothing else in your installation that is causing the oscillation first. then send it back for a replacement if you cannot fix fromthese things. Also, did you put the switching back to the "operation mode" or is it possible that you missed a step in setup? I have seen a couple of different types of setups, and usually there is a final "operation setting" for all of the universal electronic units I have seen. Good luck. Remove "YOURPANTIES" to reply MUADIB® http://www.angelfire.com/retro/sster...IN%20PAGE.html one small step for man,..... One giant leap for attorneys. |
#8
|
|||
|
|||
Scott - you said "I've snapped 2 cables already because of the very tight
bend as it comes out of the gage and meets the underside metal cross member behind the dash" That makes me think the problem bouncing proble is with the cable handing up momentarily. Try rotating the gauge 45 degrees so the cable doesn't make that sharp bend and see if that corrects it. "Scott" > wrote in message oups.com... > > AS luck would have it I replaced the mechanical old VDO speedometer in > my dune buggy with the newer electronic version. After calibrating the > thing on a true mile distance and getting it to work, the needle > movement is worse than the damn gas gauge splashing around. Way to > much lag and jump in the way this works. Does anyone have such a beast > installed, and if so does it give accurate smooth speed readings. > Scott > 69' Dune Buggy > |
#9
|
|||
|
|||
"Scott" > wrote in message oups.com... > > AS luck would have it I replaced the mechanical old VDO speedometer in > my dune buggy with the newer electronic version. After calibrating the > thing on a true mile distance and getting it to work, the needle > movement is worse than the damn gas gauge splashing around. Way to > much lag and jump in the way this works. Does anyone have such a beast > installed, and if so does it give accurate smooth speed readings. > Scott > 69' Dune Buggy > Where does the sensor mount? Sounds like the most vulnerable part of the mechanical system is still used by the electronic system. The attachment to the dust cover and routing through the spindle are where I've had dozens of problems over the years, causing the cable to turn in "jumps" because of binding. Same would apply to the electronic device if the cable is still used. You've probably already checked that out a bunch of times, but it sure seems the most likely culprit. When I added new gauges to Bussy for the new engine, I went to Nordskog gauges. They are electronic, but use stepper motors to run the needles. I have not gotten around to the new speedometer yet - probably will when this current mechanical one starts to bounce! Let us know what you learn. -Bah |
#10
|
|||
|
|||
Just to reply to everyone here. Thanks for all the input. I replaced
the old mechanical VDO because of cable bend under the dash & about 5mph off on the reading. As stated before, I needed to replace with another VDO to maintain the look. Calibration worked perfect...as a few of you mentioned the cable could be spinning and hanging....I'll check on that and hopefully thats the problem. There is no cable twist in the new setup except the way it transfers out of the axle spindle, but then you can't change that. They thing that really raised a RED FLAG was when I stopped, the pointer when to zero very slowly, took 3-5 seconds. So, I have a day to play before a telephone call to VDO. Thanks everyone for the input. Scott 69' Dune Buggy |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Hondo civic, speedometer sensor fuse blowing up | [email protected] | Honda | 3 | January 15th 05 02:48 AM |
New *FREE* Corvette Discussion Forum | JLA ENTERPRISES TECHNOLOGIES INTEGRATION | Corvette | 12 | November 30th 04 06:36 PM |
92 saturn SL-2 speedometer | deast90 | Saturn | 2 | July 18th 04 03:38 AM |
speedometer recalibration | Dies Deambulo | 4x4 | 2 | March 24th 04 02:17 AM |