If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
'75 Speedo Drive Gear
Hi all,
I have noticed fluid leaking around the speedo drive area on the tranny (automatic). The service manual instructions are simply to remove cable; remove retainer bolt and clamp; and remove driven gear assy. to replace "O" ring. Trouble is that the driven assy. just doesn't "come out". After 30 years how much help can I give it with small taps without damaging the unit ? Is it keyed or splined which would mean damage from any kind of persuasion ? My Corvette Assembly Manual doesn't show this area. Thanks. |
Ads |
#2
|
|||
|
|||
I just pulled one on a '79 a month ago and it was stuck. Twist it back and
forth a few times, and pull. No tapping. You can push in slightly with your fingers also. The O-ring sticks and won't move, so you have to move it enough to break the seal and get a bit of fluid under it so it slides. When it comes loose, it will fly right out, so be ready. "W. Moore" > wrote in message ... > Hi all, > I have noticed fluid leaking around the speedo drive area on the tranny > (automatic). The service manual instructions are simply to remove cable; > remove retainer bolt and clamp; and remove driven gear assy. to replace "O" > ring. Trouble is that the driven assy. just doesn't "come out". After 30 > years how much help can I give it with small taps without damaging the unit > ? Is it keyed or splined which would mean damage from any kind of > persuasion ? My Corvette Assembly Manual doesn't show this area. Thanks. > > |
#3
|
|||
|
|||
Tom,
Thanks for the info. When you say that it will fly right out do you mean that there is a spring behind it or a lot of fluid that will spill all over ? "Tom in Missouri" > wrote in message ink.net... > I just pulled one on a '79 a month ago and it was stuck. Twist it back and > forth a few times, and pull. No tapping. > > You can push in slightly with your fingers also. The O-ring sticks and > won't move, so you have to move it enough to break the seal and get a bit of > fluid under it so it slides. > > When it comes loose, it will fly right out, so be ready. > > > "W. Moore" > wrote in message > ... > > Hi all, > > I have noticed fluid leaking around the speedo drive area on the tranny > > (automatic). The service manual instructions are simply to remove cable; > > remove retainer bolt and clamp; and remove driven gear assy. to replace > "O" > > ring. Trouble is that the driven assy. just doesn't "come out". After > 30 > > years how much help can I give it with small taps without damaging the > unit > > ? Is it keyed or splined which would mean damage from any kind of > > persuasion ? My Corvette Assembly Manual doesn't show this area. Thanks. > > > > > > |
#4
|
|||
|
|||
Not allot of fluid, just that they always seem to pop loose and it is quick
enough to cut the back of your hand as you pull on it. You do have to get it moving in and out, rotating it sometime only breaks the inside seal where it's froze fast. It is a tight metal fit and it don't take much corrosion to stick it in there good. Dad -- Life is a waste of time Time is a waste of life Get wasted all the time Have the time of your life "W. Moore" > wrote in message ... > Tom, > Thanks for the info. When you say that it will fly right out do you mean > that there is a spring behind it or a lot of fluid that will spill all > over > ? > > > "Tom in Missouri" > wrote in message > ink.net... >> I just pulled one on a '79 a month ago and it was stuck. Twist it back > and >> forth a few times, and pull. No tapping. >> >> You can push in slightly with your fingers also. The O-ring sticks and >> won't move, so you have to move it enough to break the seal and get a bit > of >> fluid under it so it slides. >> >> When it comes loose, it will fly right out, so be ready. >> >> >> "W. Moore" > wrote in message >> ... >> > Hi all, >> > I have noticed fluid leaking around the speedo drive area on the tranny >> > (automatic). The service manual instructions are simply to remove > cable; >> > remove retainer bolt and clamp; and remove driven gear assy. to replace >> "O" >> > ring. Trouble is that the driven assy. just doesn't "come out". >> > After >> 30 >> > years how much help can I give it with small taps without damaging the >> unit >> > ? Is it keyed or splined which would mean damage from any kind of >> > persuasion ? My Corvette Assembly Manual doesn't show this area. > Thanks. >> > >> > >> >> > > |
#5
|
|||
|
|||
It's not keyed.... Just wiggle around, holler and scream at it
and have someone else take a crack at it while your resting, then switch off back and forth. :-) W. Moore wrote: >Hi all, >I have noticed fluid leaking around the speedo drive area on the tranny >(automatic). The service manual instructions are simply to remove cable; >remove retainer bolt and clamp; and remove driven gear assy. to replace "O" >ring. Trouble is that the driven assy. just doesn't "come out". After 30 >years how much help can I give it with small taps without damaging the unit >? Is it keyed or splined which would mean damage from any kind of >persuasion ? My Corvette Assembly Manual doesn't show this area. Thanks. > > > > -- Ric Seyler |
#6
|
|||
|
|||
Screw the cable back on and use a pair of needle nose pliers between
the cable and case to persuade it to come out. PDeen |
#7
|
|||
|
|||
Hi again,
Many thanks to all respondents. I wrapped a piece of leather around the speedo cable threads on the housing and with a pair of channel-locks wiggled it until it popped out, no busted knuckles or cut hands. I called two Chevy dealers looking for parts. One didn't have the "O" ring, or the grease seal in the center of the housing. The second one said he had both so I jumped in the truck and drove 30 miles to that dealer. Oops was the reply when I arrived. He misunderstood what year model I had and that it was an automatic tranny and not a manual tranny. I wonder if he understood anything that I told him ! After a 60 mile round trip for nothing I called a local speed shop who told me that the inner grease seal is common for a range of Chevy auto. trans. models and he can have it in two days, and the large "O" ring is a standard "on the shelf" item. I'm hoping for good luck at that shop. "PDDeen" > wrote in message oups.com... > Screw the cable back on and use a pair of needle nose pliers between > the cable and case to persuade it to come out. > PDeen > |
#8
|
|||
|
|||
Some counter people need a good smack from time to time!! :-)
W. Moore wrote: >Hi again, >Many thanks to all respondents. I wrapped a piece of leather around the >speedo cable threads on the housing and with a pair of channel-locks wiggled >it until it popped out, no busted knuckles or cut hands. I called two Chevy >dealers looking for parts. One didn't have the "O" ring, or the grease seal >in the center of the housing. The second one said he had both so I jumped >in the truck and drove 30 miles to that dealer. Oops was the reply when I >arrived. He misunderstood what year model I had and that it was an >automatic tranny and not a manual tranny. I wonder if he understood >anything that I told him ! After a 60 mile round trip for nothing I called >a local speed shop who told me that the inner grease seal is common for a >range of Chevy auto. trans. models and he can have it in two days, and the >large "O" ring is a standard "on the shelf" item. I'm hoping for good luck >at that shop. > > > >"PDDeen" > wrote in message roups.com... > > >>Screw the cable back on and use a pair of needle nose pliers between >>the cable and case to persuade it to come out. >>PDeen >> >> >> > > > > -- Ric Seyler |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
odometer fix A1. Some notes and variations on how to | [email protected] | VW water cooled | 4 | July 11th 05 11:33 PM |
93 Sundance will not shift into any gear. | Shaun Q | Chrysler | 9 | June 29th 05 05:18 PM |
auto trans won't downshift to 1st gear on 2000 Explorer V6 SOHC | KI0FT | Ford Explorer | 3 | December 23rd 04 01:02 AM |
97 GT speedo cal with gear change 3.73/4.10/ete. ?? | no-spam | Ford Mustang | 3 | November 27th 04 11:55 AM |
Vibrations when i'm standing still on my A4 from 2000 when it is in 'drive' | Eykens Kenny | Audi | 2 | July 15th 04 05:42 AM |