A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » BMW
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Reboring /sleeving 740 4.4 engine



 
 
Thread Tools Display Modes
  #1  
Old August 29th 06, 01:04 PM posted to alt.autos.bmw
Cords
external usenet poster
 
Posts: 7
Default Reboring /sleeving 740 4.4 engine

I had unfortunate incident at a BMW dealership. Whilst sevicing My 1997
740 4.4 litre the technician accidently dropped the screw top of the
spark plug into one bore. Needless to say on start up destroyed the
head and scored the cylinder. The dealership now wants to machine the
bore and put in a metal liner.
Is this possible on a aluminium alusil engine?
I would have thought the correct thing to do would be to replace the
block or the entire engine!

Any advice would be appreciated
Cords

Ads
  #2  
Old August 29th 06, 01:19 PM posted to alt.autos.bmw
[email protected]
external usenet poster
 
Posts: 122
Default Reboring /sleeving 740 4.4 engine


Cords wrote:
> I had unfortunate incident at a BMW dealership. Whilst sevicing My 1997
> 740 4.4 litre the technician accidently dropped the screw top of the
> spark plug into one bore. Needless to say on start up destroyed the
> head and scored the cylinder. The dealership now wants to machine the
> bore and put in a metal liner.
> Is this possible on a aluminium alusil engine?
> I would have thought the correct thing to do would be to replace the
> block or the entire engine!
>
> Any advice would be appreciated
> Cords


I would have thought that the replacement option would be easier and
just as cost effective. I would guess that the piston and maybe the
con-rod is damaged too.

  #4  
Old August 29th 06, 02:29 PM posted to alt.autos.bmw
R. Mark Clayton
external usenet poster
 
Posts: 778
Default Reboring /sleeving 740 4.4 engine


> wrote in message
ups.com...
>
> Cords wrote:
>> I had unfortunate incident at a BMW dealership. Whilst sevicing My 1997
>> 740 4.4 litre the technician accidently dropped the screw top of the
>> spark plug into one bore. Needless to say on start up destroyed the
>> head and scored the cylinder. The dealership now wants to machine the
>> bore and put in a metal liner.
>> Is this possible on a aluminium alusil engine?
>> I would have thought the correct thing to do would be to replace the
>> block or the entire engine!
>>
>> Any advice would be appreciated
>> Cords

>
> I would have thought that the replacement option would be easier and
> just as cost effective. I would guess that the piston and maybe the
> con-rod is damaged too.
>


Not sure about the Alusil 4.4, but the Nikasil 4.0 can not be rebored /
sleeved because there is insufficient clearance to the oil / waterways in
the block.


  #5  
Old August 29th 06, 02:50 PM posted to alt.autos.bmw
Rex B[_1_]
external usenet poster
 
Posts: 46
Default Reboring /sleeving 740 4.4 engine


Cords wrote:
> I had unfortunate incident at a BMW dealership. Whilst sevicing My 1997
> 740 4.4 litre the technician accidently dropped the screw top of the
> spark plug into one bore. Needless to say on start up destroyed the
> head and scored the cylinder. The dealership now wants to machine the
> bore and put in a metal liner.
> Is this possible on a aluminium alusil engine?
> I would have thought the correct thing to do would be to replace the
> block or the entire engine!


You have a right to demand the car be returned to the same condition as
you brought it in, plus the work you paid them to perform. Iron
sleeving one of 8 alusil bores is NOT making you whole. You need a new
or factory reman engine, or a salvage engine of equal or lower miles,
and a guarantee with whatever they install. Do not let them sleeve your
motor.
While the piston is likely peened a little, the rod is probably OK.
But the combustion chamber in the head is also suspect.
A lot depends on the miles on your engine as to what might be a fair
replacement, but I'd assume the factory engine is good for 200K miles.
If you have had that car for 9 model years it is a reasonable assumption
that you intend to keep it for several more years.
It sounds to me like they are trying to not file an insurance
claim. They carry insurance for just this sort of thing, but of course
their claim history affects their rates and future insurability.
  #6  
Old August 29th 06, 03:03 PM posted to alt.autos.bmw
Cords
external usenet poster
 
Posts: 7
Default Reboring /sleeving 740 4.4 engine


Rex B wrote:
> Cords wrote:
> > I had unfortunate incident at a BMW dealership. Whilst sevicing My 1997
> > 740 4.4 litre the technician accidently dropped the screw top of the
> > spark plug into one bore. Needless to say on start up destroyed the
> > head and scored the cylinder. The dealership now wants to machine the
> > bore and put in a metal liner.
> > Is this possible on a aluminium alusil engine?
> > I would have thought the correct thing to do would be to replace the
> > block or the entire engine!

>
> You have a right to demand the car be returned to the same condition as
> you brought it in, plus the work you paid them to perform. Iron
> sleeving one of 8 alusil bores is NOT making you whole. You need a new
> or factory reman engine, or a salvage engine of equal or lower miles,
> and a guarantee with whatever they install. Do not let them sleeve your
> motor.
> While the piston is likely peened a little, the rod is probably OK.
> But the combustion chamber in the head is also suspect.
> A lot depends on the miles on your engine as to what might be a fair
> replacement, but I'd assume the factory engine is good for 200K miles.
> If you have had that car for 9 model years it is a reasonable assumption
> that you intend to keep it for several more years.
> It sounds to me like they are trying to not file an insurance
> claim. They carry insurance for just this sort of thing, but of course
> their claim history affects their rates and future insurability.


Thanks...my thoughts exactly!...They talk about replacing the head with
a second hand one which they will check. The Car has only done 62 000
miles and all long distance so the engine was like new...very
Disappointing to say the least

  #7  
Old August 29th 06, 03:14 PM posted to alt.autos.bmw
Branden Nelsen
external usenet poster
 
Posts: 30
Default Reboring /sleeving 740 4.4 engine

I agree, that sleeving is a cheap way out and they know it. I would demand
that they replace the engine with a new engine, especially since the old
engine was taken care of from the sounds of it. If not im sure your lawyer
can make them see the light


-Branden


"Cords" > wrote in message
ps.com...
>
> Rex B wrote:
>> Cords wrote:
>> > I had unfortunate incident at a BMW dealership. Whilst sevicing My 1997
>> > 740 4.4 litre the technician accidently dropped the screw top of the
>> > spark plug into one bore. Needless to say on start up destroyed the
>> > head and scored the cylinder. The dealership now wants to machine the
>> > bore and put in a metal liner.
>> > Is this possible on a aluminium alusil engine?
>> > I would have thought the correct thing to do would be to replace the
>> > block or the entire engine!

>>
>> You have a right to demand the car be returned to the same condition as
>> you brought it in, plus the work you paid them to perform. Iron
>> sleeving one of 8 alusil bores is NOT making you whole. You need a new
>> or factory reman engine, or a salvage engine of equal or lower miles,
>> and a guarantee with whatever they install. Do not let them sleeve your
>> motor.
>> While the piston is likely peened a little, the rod is probably OK.
>> But the combustion chamber in the head is also suspect.
>> A lot depends on the miles on your engine as to what might be a fair
>> replacement, but I'd assume the factory engine is good for 200K miles.
>> If you have had that car for 9 model years it is a reasonable assumption
>> that you intend to keep it for several more years.
>> It sounds to me like they are trying to not file an insurance
>> claim. They carry insurance for just this sort of thing, but of course
>> their claim history affects their rates and future insurability.

>
> Thanks...my thoughts exactly!...They talk about replacing the head with
> a second hand one which they will check. The Car has only done 62 000
> miles and all long distance so the engine was like new...very
> Disappointing to say the least
>



  #8  
Old August 29th 06, 04:53 PM posted to alt.autos.bmw
Fred W[_1_]
external usenet poster
 
Posts: 210
Default Reboring /sleeving 740 4.4 engine

Cords wrote:
> I had unfortunate incident at a BMW dealership. Whilst sevicing My 1997
> 740 4.4 litre the technician accidently dropped the screw top of the
> spark plug into one bore. Needless to say on start up destroyed the
> head and scored the cylinder. The dealership now wants to machine the
> bore and put in a metal liner.
> Is this possible on a aluminium alusil engine?
> I would have thought the correct thing to do would be to replace the
> block or the entire engine!
>
> Any advice would be appreciated
> Cords
>


No. You can't resleeve an engine that does not have sleeves. The
Alusil or Nikasil engines are alloy blocks with a very thin coating in
the bores. Not sleeves.

They will find this was a very expensive mistake. New short block, new
head. Big bucks.

--
-Fred W
  #9  
Old August 29th 06, 05:57 PM posted to alt.autos.bmw
Jim[_11_]
external usenet poster
 
Posts: 8
Default Reboring /sleeving 740 4.4 engine


"Fred W" > wrote in message
...
> Cords wrote:
>> I had unfortunate incident at a BMW dealership. Whilst sevicing My 1997
>> 740 4.4 litre the technician accidently dropped the screw top of the
>> spark plug into one bore. Needless to say on start up destroyed the
>> head and scored the cylinder. The dealership now wants to machine the
>> bore and put in a metal liner.
>> Is this possible on a aluminium alusil engine?
>> I would have thought the correct thing to do would be to replace the
>> block or the entire engine!
>>
>> Any advice would be appreciated
>> Cords
>>

>
> No. You can't resleeve an engine that does not have sleeves. The Alusil
> or Nikasil engines are alloy blocks with a very thin coating in the bores.
> Not sleeves.
>
> They will find this was a very expensive mistake. New short block, new
> head. Big bucks.
>
> --
> -Fred W

These engines are made from an aluminum alloy that has copious quantities of
a very hard material (forget which one). Anyway, a very thin layer of hard
material forms the wear surface. Go through that, and you are left with
aluminum which is a very very very poor choice for wear.

Jim


  #10  
Old August 29th 06, 06:49 PM posted to alt.autos.bmw
Rex B[_1_]
external usenet poster
 
Posts: 46
Default Reboring /sleeving 740 4.4 engine

Fred W wrote:
> Cords wrote:
>> I had unfortunate incident at a BMW dealership. Whilst sevicing My 1997
>> 740 4.4 litre the technician accidently dropped the screw top of the
>> spark plug into one bore. Needless to say on start up destroyed the
>> head and scored the cylinder. The dealership now wants to machine the
>> bore and put in a metal liner.
>> Is this possible on a aluminium alusil engine?
>> I would have thought the correct thing to do would be to replace the
>> block or the entire engine!
>>
>> Any advice would be appreciated
>> Cords
>>

>
> No. You can't resleeve an engine that does not have sleeves.


Sure you can. It was routine back when Vegas roamed the earth.
Still is a big business when you need to reclaim an otherwise good block
that might not be replaceable. It is a common, weekly operation at any
automotive machine shop.

But even then they didn't sleeve just the one bad cylinder.
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Recommendations for Jeep Mechanic near Edison, NJ [email protected] Jeep 1 July 30th 06 07:10 PM
Why you should never buy a car without a tachometer Ted B. Driving 112 September 19th 05 04:09 AM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 3 February 18th 05 06:34 AM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 4 February 2nd 05 06:22 AM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 10 December 18th 04 06:15 AM


All times are GMT +1. The time now is 10:01 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.