If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
2001 300m passenger door handle(inside)
Chrome plating peeling off and is very sharp, in fact I cut my hand on it.
The dealer wants $140.00 to replace it. Seems like an awful lot to me, any suggestions? |
Ads |
#2
|
|||
|
|||
Fiberman wrote:
> Chrome plating peeling off and is very sharp, in fact I cut my hand on it. > The dealer wants $140.00 to replace it. Seems like an awful lot to me, any > suggestions? > > Are they maybe saying they have to replace the whole door panel just to get a new handle? I think I've seen posts on dodgeintrepid.net and the 300M Enthusiasts forums saying that, but also that if you're skillful, you can get one out of a panel in a junk yard and figure out how to reinstall it - the problem is that the pivot pin, rivet or whatever that holds it in the panel, is not made to be serviced (removed/replaced), but you can do it with a little ingenuity. Another option would be to find the whole panel in good shape out of a junk yard, but it would take a little luck to find one of the same color, etc. Bill Putney (To reply by e-mail, replace the last letter of the alphabet in my adddress with the letter 'x') |
#3
|
|||
|
|||
"Bill Putney" > wrote in message ... > Fiberman wrote: > > Chrome plating peeling off and is very sharp, in fact I cut my hand on it. > > The dealer wants $140.00 to replace it. Seems like an awful lot to me, any > > suggestions? > > > > > > Are they maybe saying they have to replace the whole door panel just to > get a new handle? I think I've seen posts on dodgeintrepid.net and the > 300M Enthusiasts forums saying that, but also that if you're skillful, > you can get one out of a panel in a junk yard and figure out how to > reinstall it - the problem is that the pivot pin, rivet or whatever that > holds it in the panel, is not made to be serviced (removed/replaced), > but you can do it with a little ingenuity. > > Another option would be to find the whole panel in good shape out of a > junk yard, but it would take a little luck to find one of the same > color, etc. > > Bill Putney > (To reply by e-mail, replace the last letter of the alphabet in my > adddress with the letter 'x') The handles were part of the door panel at one time, now they are available seperate, I beleive they were about 40.00, but dont quote me on it SUBJECT: Interior Front Door Handle/Bezel Replacement OVERVIEW: This bulletin provides information to allow replacement of interior front door handle/bezel instead of replacement of the door trim panel. MODELS: 1998 - **2004** (LH) LHS/300M/Concorde/Intrepid SYMPTOM/CONDITION: An interior front door handle/bezel requires replacement. **PARTS REQUIRED: Qty. Part No. Description AR 05102832AA Handle/Bezel, Left, Intrepid, Agate, Trim Codes AZ or D5 AR 05102833AA Handle/Bezel, Right, Intrepid, Agate, Trim Codes AZ or D5 AR 05102834AA Handle/Bezel, Right, Intrepid, Dk Camel, Trim Code K9 AR 05102835AA Handle/Bezel, Left, Intrepid, Dk Camel, Trim Code K9 AR 05102836AA Handle/Bezel, Right, Intrepid, Dk Slate, Trim Code DV AR 05102837AA Handle/Bezel, Right, Intrepid, Dk Sandstone, Trim Code T5 AR 05102838AA Handle/Bezel, Right, Intrepid, Dk Taupe, Trim Code L5 AR 05102839AA Handle/Bezel, Left, Intrepid, Dk Slate, Trim Code DV AR 05102840AA Handle/Bezel, Left, Intrepid, Dk Sandstone, Trim Code T5 AR 05102841AA Handle/Bezel, Left, Intrepid, Dk Taupe, Trim Code L5 AR 05102842AA Handle/Bezel, Right, LHS/300, Agate, Trim Codes AZ or NUMBE Qty. Part No. Description D5 AR 05102844AA Handle/Bezel, Left, LHS/300M, Agate, Trim Codes AZ or D5 AR 05102845AA Handle/Bezel, Left, LHS/300M, Dk Camel, Trim Codes K9 or FK AR 05102846AA Handle/Bezel, Right, LHS/300M, Dk Camel, Trim Codes K9 or FK AR 05102847AA Handle/Bezel, Right, LHS/300M/Concorde Limited, Dk Slate, Trim Codes DV, D2 or ZA AR 05102849AA Handle/Bezel, Left, LHS/300M/Concorde Limited, Dk Slate, Trim Codes DV, D2 or ZA AR 05102850AA Handle/Bezel, Right, LHS/300M/Concorde Limited, Dk Sandstone, Trim Code T5 AR 05102851AA Handle/Bezel, Left, LHS/300M/Concorde Limited, Dk Sandstone, Trim Code T5 AR 05102852AA Handle/Bezel, Right, LHS/300M/Concorde Limited, Dk Taupe, Trim Codes L5 or L2 AR 05102853AA Handle/Bezel, Left, LHS/300M/Concorde Limited, Dk Taupe, Trim Codes L5 or L2 AR 05102854AA Handle/Bezel Woodgrain, Left, Concorde, Agate, Color Handle, Trim Codes AZ or D5 AR 05102855AA Handle/Bezel Woodgrain, Right, Concorde, Agate, Color Handle, Trim Codes AZ or D5 AR 05102856AA Handle/Bezel Woodgrain, Left, Concorde, Dk Camel, Color Handle, Trim Code K9 AR 05102857AA Handle/Bezel Woodgrain, Right, Concorde, Dk Camel, Color Handle, Trim Code K9 AR 05102858AA Handle/Bezel Woodgrain, Right, Concorde, Dk Camel, Chrome Handle, Trim Code K9 AR 05102859AA Handle/Bezel Woodgrain, Left, Concorde, Dk Camel, Chrome Handle, Trim Code K9 AR 05102860AA Handle/Bezel Woodgrain, Right, Concorde, Agate, Chrome Handle, Trim Codes AZ or D5 AR 05102861AA Handle/Bezel Woodgrain, Left, Concorde, Agate, Chrome Handle, Trim Codes AZ or D5 AR 05102862AA Handle/Bezel Woodgrain, Left, Concorde, Dk Slate, Chrome Handle, Trim Code DV AR 05102863AA Handle/Bezel Woodgrain, Right, Concorde, Dk Slate, Chrome Handle, Trim Code DV AR 05102864AA Handle/Bezel Woodgrain, Left, Concorde, Dk Sandstone, Chrome Handle, Trim Code T5 Qty. Part No. Description AR 05102865AA Handle/Bezel Woodgrain, Right, Concorde, Dk Sandstone, Chrome Handle, Trim Code T5 AR 05102866AA Handle/Bezel Woodgrain, Left, Concorde, Dk Taupe, Chrome Handle, Trim Code L5 AR 05102867AA Handle/Bezel Woodgrain, Right, Concorde, Dk Taupe, Chrome Handle, Trim Code L5 ** NOTE: Each kit contains one handle/bezel assembly, six pushnuts and an instruction sheet. SPECIAL TOOLS/EQUIPMENT REQUIRED: NPN 21/64 in. (8.3mm) Drill Bit REPAIR PROCEDU 1. Remove the front door trim panel using the procedures outlined on TechCONNECT or in Section 23 of the appropriate service manual. 2. After placing the door trim panel on a clean work surface, use a 21/64 in. drill bit to drill out the mounting boss heat stakes that attach the existing door handle/bezel to the trim panel. Take extra care to drill in the center of each heat stake, (Fig. 1). Fig. 1 DRILL 4 HEAT STAKES 3. Remove the existing handle/bezel from trim panel. 4. Clean the back of the trim panel of all plastic filings. 5. Seat the new handle/bezel into position. 6. Place the push nuts onto the handle/bezel bosses. 7. Use a 10mm socket to install the push nuts all the way down on the mounting bosses to secure the handle/bezel onto the door trim panel. Using a wiggling side to side motion may be helpful, |
#4
|
|||
|
|||
maxpower wrote:
> "Bill Putney" > wrote in message > ... > >>Fiberman wrote: >> >>>Chrome plating peeling off and is very sharp, in fact I cut my hand on > > it. > >>>The dealer wants $140.00 to replace it. Seems like an awful lot to me, > > any > >>>suggestions? >>> >>> >> >>Are they maybe saying they have to replace the whole door panel just to >>get a new handle? I think I've seen posts on dodgeintrepid.net and the >>300M Enthusiasts forums saying that, but also that if you're skillful, >>you can get one out of a panel in a junk yard and figure out how to >>reinstall it - the problem is that the pivot pin, rivet or whatever that >>holds it in the panel, is not made to be serviced (removed/replaced), >>but you can do it with a little ingenuity. >> >>Another option would be to find the whole panel in good shape out of a >>junk yard, but it would take a little luck to find one of the same >>color, etc. >> >>Bill Putney >>(To reply by e-mail, replace the last letter of the alphabet in my >>adddress with the letter 'x') > > > The handles were part of the door panel at one time, now they are available > seperate, I beleive they were about 40.00, but dont quote me on it > > SUBJECT: > > Interior Front Door Handle/Bezel Replacement > > OVERVIEW: > > This bulletin provides information... That's good news. Sounds like the $140 they were quoted uses this replacement handle and includes the labor for the labor intensive replacement work. Bill Putney (To reply by e-mail, replace the last letter of the alphabet in my adddress with the letter 'x') |
#5
|
|||
|
|||
I didn't think you could get a door panel for $140.
"Bill Putney" > wrote in message ... > maxpower wrote: >> "Bill Putney" > wrote in message >> ... >> >>>Fiberman wrote: >>> >>>>Chrome plating peeling off and is very sharp, in fact I cut my hand on >> >> it. >> >>>>The dealer wants $140.00 to replace it. Seems like an awful lot to me, >> >> any >> >>>>suggestions? >>>> >>>> >>> >>>Are they maybe saying they have to replace the whole door panel just to >>>get a new handle? I think I've seen posts on dodgeintrepid.net and the >>>300M Enthusiasts forums saying that, but also that if you're skillful, >>>you can get one out of a panel in a junk yard and figure out how to >>>reinstall it - the problem is that the pivot pin, rivet or whatever that >>>holds it in the panel, is not made to be serviced (removed/replaced), >>>but you can do it with a little ingenuity. >>> >>>Another option would be to find the whole panel in good shape out of a >>>junk yard, but it would take a little luck to find one of the same >>>color, etc. >>> >>>Bill Putney >>>(To reply by e-mail, replace the last letter of the alphabet in my >>>adddress with the letter 'x') >> >> >> The handles were part of the door panel at one time, now they are >> available >> seperate, I beleive they were about 40.00, but dont quote me on it >> >> SUBJECT: >> >> Interior Front Door Handle/Bezel Replacement >> >> OVERVIEW: >> >> This bulletin provides information... > > That's good news. Sounds like the $140 they were quoted uses this > replacement handle and includes the labor for the labor intensive > replacement work. > > Bill Putney > (To reply by e-mail, replace the last letter of the alphabet in my > adddress with the letter 'x') |
#7
|
|||
|
|||
Art wrote:
> I didn't think you could get a door panel for $140. > You're right. Bill Putney (To reply by e-mail, replace the last letter of the alphabet in my adddress with the letter 'x') |
#8
|
|||
|
|||
The Commander wrote:
> WARRANTY!!!! Be kewl with the service manager and they will > do it as "good will" towards the customers. > One thing I do is take my cars to the dealers and get my oil changed > when they send me cheap coupons... so when I have problems they > know me and do stuff for free for me. And end up with stripped out oil pan drain plug threads? No thanks. Bill Putney (To reply by e-mail, replace the last letter of the alphabet in my adddress with the letter 'x') |
#9
|
|||
|
|||
"Bill Putney" > wrote in message ... > The Commander wrote: > > > WARRANTY!!!! Be kewl with the service manager and they will > > do it as "good will" towards the customers. > > One thing I do is take my cars to the dealers and get my oil changed > > when they send me cheap coupons... so when I have problems they > > know me and do stuff for free for me. > > And end up with stripped out oil pan drain plug threads? No thanks. > > Bill Putney > (To reply by e-mail, replace the last letter of the alphabet in my > adddress with the letter 'x') Bill are you saying that the dealers are the only ones that strip plugs?? |
#10
|
|||
|
|||
My Chrysler dealer has never stripped the threads changing oil. They have
spilled oil all over the place though and one time the smoke was so bad I had to pull over and make sure the engine wasn't on fire. "Bill Putney" > wrote in message ... > The Commander wrote: > >> WARRANTY!!!! Be kewl with the service manager and they will >> do it as "good will" towards the customers. >> One thing I do is take my cars to the dealers and get my oil changed >> when they send me cheap coupons... so when I have problems they >> know me and do stuff for free for me. > > And end up with stripped out oil pan drain plug threads? No thanks. > > Bill Putney > (To reply by e-mail, replace the last letter of the alphabet in my > adddress with the letter 'x') |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Analogies, trains and FIRST-Racing... | Tony Rickard | Simulators | 50 | April 4th 05 04:38 AM |
"Al Qaeda" does not exist | Awake | BMW | 64 | March 10th 05 11:25 AM |
Flasher ? for 2001 up/Led Taillights | Intergate | Jeep | 7 | February 15th 05 07:00 PM |
2001 Ford Mustang - Passenger Window | Lewis | Ford Mustang | 0 | November 27th 04 11:41 PM |