A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto newsgroups » 4x4
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Replacing leaf springs and maintaining OEM ride height



 
 
Thread Tools Display Modes
  #1  
Old April 27th 06, 04:34 AM posted to rec.autos.4x4
external usenet poster
 
Posts: n/a
Default Replacing leaf springs and maintaining OEM ride height

I've baffled the online 'experts' by asking if a particular set of
leaf springs will maintain the OEM ride height of my 97 Tacoma 4WD.
I was particularly interested in a set of Pro Comp springs (price is a
factor at only $110 a pop)
They are advertised as having a height of 3.5", but when I questioned
customer service as to whether this was the same as stock, they
couldn't answer.
It's a 4-leaf set, so I'm thinking it can't be much different than
stock, but I don't want a jacked up rear end if I get these things (I'm
currently a leaf short due to hauling too much firewood)

Anyone have some insight as to what to expect/look for in aftermarket
springs?
I don't want to "trick my truck" - just give it some extra carrying
capacity.

Ads
  #2  
Old April 27th 06, 12:35 PM posted to rec.autos.4x4
external usenet poster
 
Posts: n/a
Default Replacing leaf springs and maintaining OEM ride height

On 26 Apr 2006 20:34:28 -0700, "northcountry"
> wrote:

>I've baffled the online 'experts' by asking if a particular set of
>leaf springs will maintain the OEM ride height of my 97 Tacoma 4WD.
>I was particularly interested in a set of Pro Comp springs (price is a
>factor at only $110 a pop)
>They are advertised as having a height of 3.5", but when I questioned
>customer service as to whether this was the same as stock, they
>couldn't answer.
>It's a 4-leaf set, so I'm thinking it can't be much different than
>stock, but I don't want a jacked up rear end if I get these things (I'm
>currently a leaf short due to hauling too much firewood)
>
>Anyone have some insight as to what to expect/look for in aftermarket
>springs?
>I don't want to "trick my truck" - just give it some extra carrying
>capacity.


When you lok at springs to compare them you must consider the number
of leafs in the and the thickness and width of them as well when
estimating ride quaility comparison. Also, the amount of arch in
spring together with its makeup will determine its ride height. Even
adding on leaf can add a lot of stiffness to them as ride firmess come
from the spring rate and the fricton between the leafs as well.
-----------------
The SnoMan
www.thesnoman.com
  #3  
Old April 27th 06, 03:16 PM posted to rec.autos.4x4
external usenet poster
 
Posts: n/a
Default Replacing leaf springs and maintaining OEM ride height

??????

When a spring is listed at 3.5 or 4.5 or 2, it is the amount of lift you
can expect 'above' stock.

A 3.5" lift spring will jack the rear end wayyyy up there.

Why not just get another set of stock springs? They are 'usually' the
strongest out there. If you go to a spring shop, they can even change
out one or more of the stock leafs to make it a 'heavy duty' spring set.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)

northcountry wrote:
>
> I've baffled the online 'experts' by asking if a particular set of
> leaf springs will maintain the OEM ride height of my 97 Tacoma 4WD.
> I was particularly interested in a set of Pro Comp springs (price is a
> factor at only $110 a pop)
> They are advertised as having a height of 3.5", but when I questioned
> customer service as to whether this was the same as stock, they
> couldn't answer.
> It's a 4-leaf set, so I'm thinking it can't be much different than
> stock, but I don't want a jacked up rear end if I get these things (I'm
> currently a leaf short due to hauling too much firewood)
>
> Anyone have some insight as to what to expect/look for in aftermarket
> springs?
> I don't want to "trick my truck" - just give it some extra carrying
> capacity.

  #4  
Old April 27th 06, 05:31 PM posted to rec.autos.4x4
external usenet poster
 
Posts: n/a
Default Replacing leaf springs and maintaining OEM ride height

When I need springs, I go to the local truck spring shops. The ones
that do dump trucks and Semi tractors. I busted some leafs out of my
1/2 ton Chevy and got a replacement 'stock' set installed for $200.00.

I then needed to replace my busted ones in my CJ7, so I went back to the
same place. They got 'stock' leafs, arched them for a 2.5" lift and
replaced one leaf with a pre arched 'keeper' leaf and installed them all
for under $250.00 a pair. These are in Canadian dollars too.

One would think the off road and 4x4 shops imagine their springs are
gold plated or something like the dealer does for the foolish amounts of
money they want.

The truck spring shops might be able to save you big also if your top
leaf is still intact. They can just replace the lower pack for a lot
less than a full set.

Mike

northcountry wrote:
>
> My search for "stock springs" leads to the Toyota dealer, where they
> got for over $400.00 each!
>
> Another possibility is Wheeler Offroad - they have a pair of 4 spring
> leafs that are close to ride height and go for $329 a pair
> http://www.wheelersoffroad.com/tacoleafs.htm
>
> Anyone have experience with their stuff?
>
> Mike Romain wrote:
> > ??????
> >
> > When a spring is listed at 3.5 or 4.5 or 2, it is the amount of lift you
> > can expect 'above' stock.
> >
> > A 3.5" lift spring will jack the rear end wayyyy up there.
> >
> > Why not just get another set of stock springs? They are 'usually' the
> > strongest out there. If you go to a spring shop, they can even change
> > out one or more of the stock leafs to make it a 'heavy duty' spring set.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > northcountry wrote:
> > >
> > > I've baffled the online 'experts' by asking if a particular set of
> > > leaf springs will maintain the OEM ride height of my 97 Tacoma 4WD.
> > > I was particularly interested in a set of Pro Comp springs (price is a
> > > factor at only $110 a pop)
> > > They are advertised as having a height of 3.5", but when I questioned
> > > customer service as to whether this was the same as stock, they
> > > couldn't answer.
> > > It's a 4-leaf set, so I'm thinking it can't be much different than
> > > stock, but I don't want a jacked up rear end if I get these things (I'm
> > > currently a leaf short due to hauling too much firewood)
> > >
> > > Anyone have some insight as to what to expect/look for in aftermarket
> > > springs?
> > > I don't want to "trick my truck" - just give it some extra carrying
> > > capacity.

  #5  
Old April 27th 06, 10:58 PM posted to rec.autos.4x4
external usenet poster
 
Posts: n/a
Default Replacing leaf springs and maintaining OEM ride height

On Thu, 27 Apr 2006 12:31:28 -0400, Mike Romain >
wrote:

>When I need springs, I go to the local truck spring shops. The ones
>that do dump trucks and Semi tractors. I busted some leafs out of my
>1/2 ton Chevy and got a replacement 'stock' set installed for $200.00.



This is a good tip. I get all my spring parts at a local spring shop
and have my leafs cut and arched to my needs. I freind bought a 2500HD
and was diappoint with the rear springs and we had a new extra leaf
cut and arched for each side on the length we wanted and it cost us 70
bucks total for the springs and new center eye bolts and we installed
them ourself with my air tools in less than a hour when truck was less
than a week old.
-----------------
The SnoMan
www.thesnoman.com
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 09:03 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.