If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
'00 SOHC torque < '98 SOHC torque?
i have a 2000 ford explorer sport with the Standard OverHead Cam
enginel. it runs great (other than the fact that it whistles a little bit at around 3000 RPM at about 50% throttle) and has not required any engine work since i bought the vehicle. However, the I dont seem to get as much low end torque from it as i can from the 1998 4Door XLT with the same engine. I even have a K&N air filter and Flowmaster exhaust on it and the low end torque still doesnt match the stock '98 XLT's. Is there anything wrong with my Sport's engine? Is the whistling a possible vacuum leak? Could my engine timing be off any? Any help would be greatly appreciated. almfreak by the way, i changed the plugs in the Sport less than 2 months ago hoping it would help, and yes they are properly gapped |
Ads |
#2
|
|||
|
|||
'00 SOHC torque < '98 SOHC torque?
I know that problem. Sounds exactly like my '97 Limited with 104,000
kms. I looked around the group for files and info and I narrowed it down to the IAC (idle air control). I can't remember where the info is but it is here somewhere. The IAC is a flanged device with a wired connector on the opposite end of the two-bolt flange in the air intake pipe after the throttle body. Disconnect the connector (don't force it, it unplugs easy once you release the lock right) and remove it by loosening the two bolts with a 10 mm spanner of box wrench. There is also what looks like a black knob on the side of it. Its isn't a knob. its the housing for the felt wad that serves as some kind of air filtre. The black outer cylinder comes off with a little persistent but careful pulling. Wash off the felt pad with detergent (dishwashing stuff works) and set it aside to dry. Set the IAC itself on some kind of metal pan and spray liberally with carburator cleaner. You should get quite a collection of soot and dirt. I air dry it with canned air--photographer's stuff. I know, I know, thats pricey. You can use shop air too but be careful the thing doesnt get blown away and into the floor. Spray the bits inside the flanged ports with some wd40 or something similar and reinstall in reverse order. You will notice that the problem won't immediately go away albeit a distinct reduction in the whistling. Drive around a bit and it eventually goes away. i hope this helps. wrote: > i have a 2000 ford explorer sport with the Standard OverHead Cam > enginel. it runs great (other than the fact that it whistles a little > bit at around 3000 RPM at about 50% throttle) and has not required any > engine work since i bought the vehicle. However, the I dont seem to > get as much low end torque from it as i can from the 1998 4Door XLT > with the same engine. I even have a K&N air filter and Flowmaster > exhaust on it and the low end torque still doesnt match the stock '98 > XLT's. Is there anything wrong with my Sport's engine? Is the > whistling a possible vacuum leak? Could my engine timing be off any? > Any help would be greatly appreciated. > > almfreak > > by the way, i changed the plugs in the Sport less than 2 months ago > hoping it would help, and yes they are properly gapped |
#4
|
|||
|
|||
'00 SOHC torque < '98 SOHC torque?
Thanks guys for the help, i'll be sure to check the axle ratio on the
'98 and see if it has any different gearing. As far as the weight, i dont think the 2 door explorer sport would weigh more than the 4 door explorer XLT. But thanks for the tips anyway. I'll be sure to check it out! thanks, almfreak |
#5
|
|||
|
|||
'00 SOHC torque < '98 SOHC torque?
Thanks guys for the help, i'll be sure to check the axle ratio on the
'98 and see if it has any different gearing. As far as the weight, i dont think the 2 door explorer sport would weigh more than the 4 door explorer XLT. But thanks for the tips anyway. I'll be sure to check it out! thanks, almfreak |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
94 1.8 rev limiter. | Mal Osborne | Mazda | 24 | May 24th 06 03:43 PM |
The engine and the electric motor | Triple-MIGHT | General | 2 | February 12th 06 08:14 AM |
to change a Honda Accord 1988 model timing belt | Jacko | Honda | 132 | November 30th 05 06:20 PM |
Further car simulator questions | Thomas Harte | Simulators | 2 | November 12th 05 01:53 AM |
Command-trac 4Hi usage questions | Sandstone | Jeep | 23 | September 7th 05 11:31 AM |