If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Research Qs on my 91 16V AT valve body....LONG and semi-Technical
First off........is anyone selling an automatic transmission valve body for
me to examine? <g> How much power is supplied to the solenoids and AT fluid temperature inside of the transmission? Is it possible to activate the solenoids at the valve body's wiring plug with an external power supply to check the operation of the individual solenoids? From my testing of the wiring, I did a test of the valve body wiring at the transmission plug. I got a slightly high reading of 70 and 68 Ohms for Solenoids #2 and #4 (should be 55-65 Ohms) I will also have to recheck #6 solenoid and I wonder why it uses a different power supply pin from everything else inside of the valve body even the AT fluid temp sensor. AND THAT IS THE ONLY SOLENOID NOT CREATING A DTC. Is this correct??? I kinda want to imagine what is happening before I pull out the valve body. (Total of 10 pins/terminals at the Valve Body Wiring Plug) Solenoids 1-TCM pin 22 2-TCM pin 23 3-TCM pin 3 4-TCM pin 2 5-TCM pin 24 6-TCM pin 25 7-TCM pin 21 1 pin - ATF temperature sensor uses TCM pins 30 +31 (TCM pin 31 is not recorded in the Bentley wiring diagram) 2 pins used for power supply at the Valve Body Wiring Plug both originate from TCM pin 18 (#6 solenoid uses 1 of the these pins, while all the other solenoids and temperature sensor uses the other) TCM pin 18 supplies the power to the solenoids and the other pins ground them out as needed. Here are the results of my DTCs that force my trans to be put in 3H (Limp Mode) VAG-COM Version: Release 303.1 Control Module Part Number: 096 927 731 M Component and/or Version: DIGIMAT 0811 Software Coding: Diagnose VW Work Shop Code: 7 Faults Found: 00258 - Solenoid Valve 1 (N88) 36-00 - Open Circuit 00260 - Solenoid Valve 2 (N89) 36-00 - Open Circuit 00262 - Solenoid Valve 3 (N90) 36-00 - Open Circuit 00264 - Solenoid Valve 4 (N91) 36-00 - Open Circuit 00266 - Solenoid Valve 5 (N92) 36-00 - Open Circuit 00270 - Solenoid Valve 7 (N94) 36-00 - Open Circuit 00300 - Transmission Fluid Temp. Sensor (G93) 34-00 - No Malfunction Detected |
Ads |
#2
|
|||
|
|||
Dave, you oughtta copy this entire post and paste it into a message on
the tech auto tranny forum on vortex, if you haven't already. Hopefully Tantalus will read and respond. He knows all. Hope you figure out your troubles (saw your posts in yahoo, too). 'luck - Chris One out of many daves wrote: > First off........is anyone selling an automatic transmission valve body for > me to examine? <g> > > How much power is supplied to the solenoids and AT fluid temperature inside > of the transmission? > Is it possible to activate the solenoids at the valve body's wiring plug > with an external power supply to check the operation of the individual > solenoids? > > From my testing of the wiring, I did a test of the valve body wiring at the > transmission plug. > I got a slightly high reading of 70 and 68 Ohms for Solenoids #2 and #4 > (should be 55-65 Ohms) > I will also have to recheck #6 solenoid and I wonder why it uses a different > power supply pin from everything else inside of the valve body even the AT > fluid temp sensor. AND THAT IS THE ONLY SOLENOID NOT CREATING A DTC. > Is this correct??? I kinda want to imagine what is happening before I pull > out the valve body. > > (Total of 10 pins/terminals at the Valve Body Wiring Plug) > > Solenoids > 1-TCM pin 22 > 2-TCM pin 23 > 3-TCM pin 3 > 4-TCM pin 2 > 5-TCM pin 24 > 6-TCM pin 25 > 7-TCM pin 21 > > 1 pin - ATF temperature sensor uses TCM pins 30 +31 (TCM pin 31 is not > recorded in the Bentley wiring diagram) > 2 pins used for power supply at the Valve Body Wiring Plug both originate > from TCM pin 18 > (#6 solenoid uses 1 of the these pins, while all the other solenoids > and temperature sensor uses the other) > TCM pin 18 supplies the power to the solenoids and the other pins ground > them out as needed. > > Here are the results of my DTCs that force my trans to be put in 3H (Limp > Mode) > > VAG-COM Version: Release 303.1 > > Control Module Part Number: 096 927 731 M > Component and/or Version: DIGIMAT 0811 > Software Coding: Diagnose VW > Work Shop Code: > 7 Faults Found: > 00258 - Solenoid Valve 1 (N88) > 36-00 - Open Circuit > 00260 - Solenoid Valve 2 (N89) > 36-00 - Open Circuit > 00262 - Solenoid Valve 3 (N90) > 36-00 - Open Circuit > 00264 - Solenoid Valve 4 (N91) > 36-00 - Open Circuit > 00266 - Solenoid Valve 5 (N92) > 36-00 - Open Circuit > 00270 - Solenoid Valve 7 (N94) > 36-00 - Open Circuit > 00300 - Transmission Fluid Temp. Sensor (G93) > 34-00 - No Malfunction Detected > > |
#3
|
|||
|
|||
thanks Chris
I will try that route also. ;-) later, dave (One out of many daves) "starburst" > wrote in message ... > Dave, you oughtta copy this entire post and paste it into a message on the > tech auto tranny forum on vortex, if you haven't already. Hopefully > Tantalus will read and respond. He knows all. Hope you figure out your > troubles (saw your posts in yahoo, too). > > 'luck - Chris > > One out of many daves wrote: >> First off........is anyone selling an automatic transmission valve body >> for >> me to examine? <g> |
#4
|
|||
|
|||
Just in case I did not close this thread, and someone was waiting for the
solution............... It was damaged insulation allowing water and dirt to create electrical problems with the auto trans shifting correctly. http://vwdoc1.tripod.com/personal/in...into_trans.jpg FIXED now, but I removed the Valve Body harness to thoroughly inspect it. http://vwdoc1.tripod.com/personal/in...ess_sealed.jpg The Valve Body was fine! later all, dave (One out of many daves) |
#5
|
|||
|
|||
i bett you have a messed up round 10 pins plug at the end of the wiring
loom... i should know trust me! |
#6
|
|||
|
|||
Well thanks for the reply
It was bad/broken insulation causing a change in electrical resistance inside of the Valve Body Harness. After finding the problem, cleaning up the area and sealing it with some silicone..............ALL IS FINE AGAIN. later, dave (One out of many daves) "avishaym" > wrote in message lkaboutautos.com... >i bett you have a messed up round 10 pins plug at the end of the wiring > loom... > i should know trust me! > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
lookin 4 | butch | VW air cooled | 12 | December 16th 04 11:38 PM |
New valve body part number for infamous transaxle problems at twice the cost | John Hupp | Saturn | 3 | December 8th 04 04:04 PM |
93 SL1 Valve Body - Question | Gary Compton | Saturn | 3 | September 3rd 04 05:58 PM |
Transmission Shifts Hard - Valve Body? | Gary Compton | Saturn | 8 | August 21st 04 07:04 PM |