If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Steering Rack Boot Replacement (clamp & tools)
Have you ever replaced the steering arm boot on a FWD vehicle?
I'm going to replace a Toyota steering arm boot for a friend (yes, I'm aware a mechanic would replace the entire arm - let's not go there please) and I have a question about the inside large steel clamp & tools. https://www.toyotapartsdeal.com/oem/...080-46293.html https://parts.toyota.com/p/Toyota_20...008046293.html It's a Toyota (I'm not sure the make but maybe a Camry of the early 2000s). The friend is buying the parts at the dealer so they'll all be OEM. 45535-06030 steering boot 90080-46293 big clamp 90467-19021 small clamp My question is about the large clamp. I don't have specialized clamp tools and like most people, I'm leery of zip ties as are others as shown here. https://youtu.be/m_iIkZEl6qY?t=293 I can find all sorts of specialized clamps on Amazon but I don't know _which_ is the specialized clamp I'd need for a Toyota clamp. https://www.amazon.com/Lisle-30600-O.../dp/B0080J1200 https://www.amazon.com/Supercrazy-Cl...dp/B01GM9PLZQ/ Maybe I can make do with pliers but maybe not. Maybe I can make do with a typical worm gear hose clamp but maybe not. Everything (as you know) depends on the amount of room and what it may touch as the boot itself tore for a reason (probably from bouncing against metal). (Why these boots tear is beyond me as you'd think they'd be designed to not touch anything while driving.) Anyway, do you have advice as to what kind of clamp tools are needed? -- "Old pinballers never die, they just flip out." |
Ads |
#2
|
|||
|
|||
Steering Rack Boot Replacement (clamp & tools)
If I have to, I'll use whatever pliers or channellocks that I have.
But I'm sure there isn't much room which will be the real problem I think. I looked at a few DIY videos (but by no means all) where about half used the plastic zip ties which I think won't hold up with cold, heat & oil around. The other half used a metal clamp, about half of which used a typical hose clamp worm gear type (which will hold up but which have sharp bouncy ends). The rest used a steel clamp that came with the package but none (so far) showed how they tightened/crimped that steel clamp but this one vide. https://youtu.be/m_iIkZEl6qY?t=293 Notice he only needed to _pull_ tightly on the end to tighten that clamp! For just pulling on a wire to close a hose clamp I might not need much room. But where do I get those pull-type hose clamps? -- "Old pinballers never die, they just flip out." |
#3
|
|||
|
|||
Steering Rack Boot Replacement (clamp & tools)
John Robertson wrote:
> If I have to, I'll use whatever pliers or channellocks that I have. > But I'm sure there isn't much room which will be the real problem I > think. > > I looked at a few DIY videos (but by no means all) where about half > used the > plastic zip ties which I think won't hold up with cold, heat & oil > around. > > The other half used a metal clamp, about half of which used a > typical hose > clamp worm gear type (which will hold up but which have sharp > bouncy ends). > > The rest used a steel clamp that came with the package but none (so > far) > showed how they tightened/crimped that steel clamp but this one vide. > https://youtu.be/m_iIkZEl6qY?t=293 > > Notice he only needed to _pull_ tightly on the end to tighten that > clamp! > > For just pulling on a wire to close a hose clamp I might not need > much room. > But where do I get those pull-type hose clamps? Quit watching videos. Do what any pinball game man would do. Hire a mechanic, play pinball for an hour, and voila ... done. |
#4
|
|||
|
|||
Steering Rack Boot Replacement (clamp & tools)
John Robertson wrote:
> If I have to, I'll use whatever pliers or channellocks that I have. > But I'm sure there isn't much room which will be the real problem I think. > > I looked at a few DIY videos (but by no means all) where about half used the > plastic zip ties which I think won't hold up with cold, heat & oil around. > > The other half used a metal clamp, about half of which used a typical hose > clamp worm gear type (which will hold up but which have sharp bouncy ends). > > The rest used a steel clamp that came with the package but none (so far) > showed how they tightened/crimped that steel clamp but this one vide. > https://youtu.be/m_iIkZEl6qY?t=293 > > Notice he only needed to _pull_ tightly on the end to tighten that clamp! > > For just pulling on a wire to close a hose clamp I might not need much room. > But where do I get those pull-type hose clamps? Those are common crimp type clamps. The tool used looks similar in action to the end nippers used to trim horses hooves. Very likely you can find the parts store version on the rack in the store or as a loaner tool or both. They are very common as they are used on those as well as CV boot clamps. To assemble them you put the slots over the ears on the clamp and then use the tool on the raised area to crimp the band just so it doesn't move in the groove. You don't want it real tight as you can damage the boot, but you want it tight enough that is doesn't leak. This is the same tool used for the CV boots that is used with the smaller rack boot clamps. https://www.youtube.com/watch?v=uHlkv9kdVhY -- Steve W. |
#5
|
|||
|
|||
Steering Rack Boot Replacement (clamp & tools)
On 2021/06/03 7:46 pm, Steve W. wrote:
> This is the same tool used for the CV boots that is used with the > smaller rack boot clamps. > https://www.youtube.com/watch?v=uHlkv9kdVhY I like your idea of seeing if I can get it as a loaner tool. And that video was pretty good in that it was as real as real can get. But what scares me is the video you provided shows the guy cursing away at the clamp even as he has the entire shaft right in front of him on the desk! https://youtu.be/uHlkv9kdVhY?t=1825 Can you imagine how difficult it would be on the vehicle? -- "Old pinballers never die, they just flip out." |
#6
|
|||
|
|||
Steering Rack Boot Replacement (clamp & tools)
John Robertson wrote:
> On 2021/06/03 7:46 pm, Steve W. wrote: >> This is the same tool used for the CV boots that is used with the >> smaller rack boot clamps. >> https://www.youtube.com/watch?v=uHlkv9kdVhY > > I like your idea of seeing if I can get it as a loaner tool. > > And that video was pretty good in that it was as real as real can get. > > But what scares me is the video you provided shows the guy cursing away at > the clamp even as he has the entire shaft right in front of him on the desk! > https://youtu.be/uHlkv9kdVhY?t=1825 > > Can you imagine how difficult it would be on the vehicle? It's really not that bad. Eric is running on the clock so anything that can mess up causes frustration. If you are doing the steering bellows it's not as bad as the parts can't wander around as you work. -- Steve W. |
#7
|
|||
|
|||
Steering Rack Boot Replacement (clamp & tools)
On Friday, June 4, 2021 at 1:29:46 AM UTC-4, John Robertson wrote:
> On 2021/06/03 7:46 pm, Steve W. wrote: > > This is the same tool used for the CV boots that is used with the > > smaller rack boot clamps. > > https://www.youtube.com/watch?v=uHlkv9kdVhY > I like your idea of seeing if I can get it as a loaner tool. > > And that video was pretty good in that it was as real as real can get. > > But what scares me is the video you provided shows the guy cursing away at > the clamp even as he has the entire shaft right in front of him on the desk! > https://youtu.be/uHlkv9kdVhY?t=1825 > > Can you imagine how difficult it would be on the vehicle? > -- > "Old pinballers never die, they just flip out." You can get boot clamps that don't require any special tools. Chas |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How long have you gone with a badly torn rubber boot in a rack and pinion steering arm? | Arlen Holder | Technology | 7 | February 1st 21 04:02 PM |
2008 Lexus Rx 350 rack and pinion steering boot | delvon daily | Technology | 4 | July 21st 20 06:12 AM |
Replace Steering Rack Boot 95 Explorer EB | plex4r | Ford Explorer | 2 | August 18th 08 10:14 PM |
Power Steering Rack Replacement | Brillo | VW water cooled | 2 | August 22nd 06 08:47 PM |
e30 steering rack boot | [email protected] | BMW | 5 | September 17th 05 05:16 PM |