If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Data on normal readings from sensors?
Hi All,
I'm working on a pesky little problem on my 2000 Chevy Astro/4.3L AWD minivan. The thing keeps lighting the MIL with a code of P0101 - something about the MAF sensor readings being out of spec. I connect my OBD-II monitor to the car and I can see the MAF go from .7 lbs/min to about 5.x lbs.minute as I accellerate, so I know that the sensor is doing something. My question is about where to find some typical readings information. I.e.: what *should* the airflow be under normal acceleration, at idle, etc. Thanks! -- TomO |
Ads |
#2
|
|||
|
|||
Data on normal readings from sensors?
In article >,
TomO > wrote: > Hi All, > > I'm working on a pesky little problem on my 2000 Chevy Astro/4.3L AWD > minivan. The thing keeps lighting the MIL with a code of P0101 - > something about the MAF sensor readings being out of spec. > > I connect my OBD-II monitor to the car and I can see the MAF go from .7 > lbs/min to about 5.x lbs.minute as I accellerate, so I know that the > sensor is doing something. > > My question is about where to find some typical readings information. > I.e.: what *should* the airflow be under normal acceleration, at idle, etc. > > Thanks! You can download a volumetric efficiency calculator here; http://www.smp-training.com/Pages/ptsframeset.html Should calculate grams per second based on RPM, temperature, engine size, air density (baro) etc. I'd plug in 85% for the (your) engines VE |
#3
|
|||
|
|||
Data on normal readings from sensors?
aarcuda69062 wrote:
> > > You can download a volumetric efficiency calculator here; > > http://www.smp-training.com/Pages/ptsframeset.html > > Should calculate grams per second based on RPM, temperature, > engine size, air density (baro) etc. I'd plug in 85% for the > (your) engines VE Thanks. If I'm using this tool correctly, I see that in order to reach near 100% Volumetric Efficiency, I would need to see about 12.5 lbs/minute at 2200 RPM and a reading of 10.7 would yield me pretty darned close to 85% VE. So it sounds like I have an airflow problem to troubleshoot, or perhaps a vacuum leak beyond the MAF sensor or something along those lines. -- TomO |
#4
|
|||
|
|||
Data on normal readings from sensors?
On Tue, 12 Sep 2006 13:37:40 -0600, TomO wrote:
> aarcuda69062 wrote: >> >> >> You can download a volumetric efficiency calculator here; >> >> http://www.smp-training.com/Pages/ptsframeset.html >> >> Should calculate grams per second based on RPM, temperature, >> engine size, air density (baro) etc. I'd plug in 85% for the >> (your) engines VE > > Thanks. > > If I'm using this tool correctly, I see that in order to reach near 100% > Volumetric Efficiency, I would need to see about 12.5 lbs/minute at 2200 > RPM and a reading of 10.7 would yield me pretty darned close to 85% VE. > > So it sounds like I have an airflow problem to troubleshoot, or perhaps > a vacuum leak beyond the MAF sensor or something along those lines. Well, I did find a vacuum leak. It was a broken plastic line that feeds the dashboard air controls. Got that patched up, but the readings from the MAF sensor did not change significantly. I'll have to dig deeper I suppose. |
#5
|
|||
|
|||
Data on normal readings from sensors?
In article >,
TomO > wrote: > aarcuda69062 wrote: > > > > > > You can download a volumetric efficiency calculator here; > > > > http://www.smp-training.com/Pages/ptsframeset.html > > > > Should calculate grams per second based on RPM, temperature, > > engine size, air density (baro) etc. I'd plug in 85% for the > > (your) engines VE > > Thanks. > > If I'm using this tool correctly, I see that in order to reach near 100% > Volumetric Efficiency, I would need to see about 12.5 lbs/minute at 2200 > RPM and a reading of 10.7 would yield me pretty darned close to 85% VE. You're not going to reach 100% volumetric efficiency with that engine. The idea is to plug in a known reasonable volumetric efficiency and then fill in the other variables to see if your air mass measurements agree with what they calculate out to be. An engine of XXX cubic inches will flow XX grams of air per second (or lbs. per hour) at XXXX RPM at XX.X barometer. > So it sounds like I have an airflow problem to troubleshoot, or perhaps > a vacuum leak beyond the MAF sensor or something along those lines. Could be a measurement problem (faulty sensor), could be the engine isn't breathing as well as it should be (coked valves, valve timing problem, restricted exhaust, restricted intake). The engine is an air pump, the mass air flow sensor give a way to measure the air being pumped thru the engine. Either the sensor is wrong, the engine can't pump its volume or the problem lies elsewhere. |
#6
|
|||
|
|||
Data on normal readings from sensors?
aarcuda69062 Wrote: > In article >, > TomO > wrote: > > > aarcuda69062 wrote: > > > > > > > > > You can download a volumetric efficiency calculator here; > > > > > > http://www.smp-training.com/Pages/ptsframeset.html > > > > > > Should calculate grams per second based on RPM, temperature, > > > engine size, air density (baro) etc. I'd plug in 85% for the > > > (your) engines VE > > > > Thanks. > > > > If I'm using this tool correctly, I see that in order to reach near > 100% > > Volumetric Efficiency, I would need to see about 12.5 lbs/minute at > 2200 > > RPM and a reading of 10.7 would yield me pretty darned close to 85% > VE. > > You're not going to reach 100% volumetric efficiency with that > engine. The idea is to plug in a known reasonable volumetric > efficiency and then fill in the other variables to see if your > air mass measurements agree with what they calculate out to be. > > An engine of XXX cubic inches will flow XX grams of air per second > (or lbs. per hour) > at XXXX RPM at XX.X barometer. > > > So it sounds like I have an airflow problem to troubleshoot, or > perhaps > > a vacuum leak beyond the MAF sensor or something along those lines. > > Could be a measurement problem (faulty sensor), could be the > engine isn't breathing as well as it should be (coked valves, > valve timing problem, restricted exhaust, restricted intake). > > The engine is an air pump, the mass air flow sensor give a way to > measure the air being pumped thru the engine. Either the sensor > is wrong, the engine can't pump its volume or the problem lies > elsewhere. That's true...I've seen crimped tailpipes cause MAF codes before...go back to basics, blow the dust off the vacuum guage and see what kind of vacuum level you are pulling... -- jeffcoslacker ------------------------------------------------------------------------ jeffcoslacker's Profile: http://www.automotiveforums.com/vbul...?userid=219638 View this thread: http://www.automotiveforums.com/vbul...d.php?t=618641 http://www.automotiveforums.com |
#7
|
|||
|
|||
Data on normal readings from sensors?
On Wed, 13 Sep 2006 18:42:11 +0000, aarcuda69062 wrote:
>> >> Thanks. >> >> If I'm using this tool correctly, I see that in order to reach near 100% >> Volumetric Efficiency, I would need to see about 12.5 lbs/minute at 2200 >> RPM and a reading of 10.7 would yield me pretty darned close to 85% VE. > > You're not going to reach 100% volumetric efficiency with that > engine. The idea is to plug in a known reasonable volumetric > efficiency and then fill in the other variables to see if your > air mass measurements agree with what they calculate out to be. Yeah, I was just working theoretical numbers to see if I was doing the calculation correct. > > An engine of XXX cubic inches will flow XX grams of air per second (or > lbs. per hour) > at XXXX RPM at XX.X barometer. > >> So it sounds like I have an airflow problem to troubleshoot, or perhaps >> a vacuum leak beyond the MAF sensor or something along those lines. I found a broken vacuum line, but repairing it did not help the readings from the sensor. It did get my dashboard air ducts working again though. > > Could be a measurement problem (faulty sensor), could be the engine > isn't breathing as well as it should be (coked valves, valve timing > problem, restricted exhaust, restricted intake). > > The engine is an air pump, the mass air flow sensor give a way to > measure the air being pumped thru the engine. Either the sensor is > wrong, the engine can't pump its volume or the problem lies elsewhere. I'll just keep on checking stuff until I come to the true source of the problem. Thanks! -- TomO |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Oxygen sensors no reading | [email protected] | Ford Explorer | 0 | June 1st 06 10:56 PM |
LIDAR Trial this Week | [email protected] | Driving | 17 | April 9th 06 02:44 AM |
88Fox correct position needle for watertemp.Gauge | Lambert Moonen | VW water cooled | 20 | February 20th 06 07:53 PM |
Inconsistent guage readings in 1977 Cherokee | Hootowl | Jeep | 11 | September 1st 05 03:35 AM |
Downstream HO2S Sensors | Lawrence Glickman | Technology | 0 | January 12th 05 09:17 PM |