If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
Thank you all!
-- Car came in with a p0301 code- mis-fire in cyl #1; and plug is burnt...-- reset codes, replaced plug, cleaned intakes with seafoam, and treated engine and fuel with Seafoam also; running now, with no codes, and idles smoothly; --- now it is ready for our master service job - front to back, -- You guys are awesum! |
Ads |
#22
|
|||
|
|||
ok,
changed fuel filter, plug #1, air filter, checked all fluids, engine still idles rough, touch the accel. and she smooths right out. Spraying a little starting fluid around the front of the intake manifold changes the idle speed instantly. have cod p301 #1 cylinder misfire again- intake gasket? --- hours for this job approx 1.7 in manual, looks like to me the upper would unbolt and lift off of intake, after you remove the EGR tubes. ---- Will be heading to allpar for info... FelPro shows and upper set... --- |
#23
|
|||
|
|||
ok,
changed fuel filter, plug #1, air filter, checked all fluids, engine still idles rough, touch the accel. and she smooths right out. Spraying a little starting fluid around the front of the intake manifold changes the idle speed instantly. have cod p301 #1 cylinder misfire again- intake gasket? --- hours for this job approx 1.7 in manual, looks like to me the upper would unbolt and lift off of intake, after you remove the EGR tubes. ---- Will be heading to allpar for info... FelPro shows and upper set... --- |
#24
|
|||
|
|||
ok,
changed fuel filter, plug #1, air filter, checked all fluids, engine still idles rough, touch the accel. and she smooths right out. Spraying a little starting fluid around the front of the intake manifold changes the idle speed instantly. have cod p301 #1 cylinder misfire again- intake gasket? --- hours for this job approx 1.7 in manual, looks like to me the upper would unbolt and lift off of intake, after you remove the EGR tubes. ---- Will be heading to allpar for info... FelPro shows and upper set... --- |
#25
|
|||
|
|||
ok,
changed fuel filter, plug #1, air filter, checked all fluids, engine still idles rough, touch the accel. and she smooths right out. Spraying a little starting fluid around the front of the intake manifold changes the idle speed instantly. have cod p301 #1 cylinder misfire again- intake gasket? --- hours for this job approx 1.7 in manual, looks like to me the upper would unbolt and lift off of intake, after you remove the EGR tubes. ---- Will be heading to allpar for info... FelPro shows and upper set... --- |
#26
|
|||
|
|||
both upper and lower intake gaskets are
leaking -- both brittle and hard. ordered the thermo gasket, the egr tube gaskets, the fuel rail gaskets, plugs, and wires; since we are here.... hardest part is getting the old gasket off.... -- my 98 Ram 5.9l intake is leaking-- suppose you guys can talk me into going it...? --- |
#27
|
|||
|
|||
both upper and lower intake gaskets are
leaking -- both brittle and hard. ordered the thermo gasket, the egr tube gaskets, the fuel rail gaskets, plugs, and wires; since we are here.... hardest part is getting the old gasket off.... -- my 98 Ram 5.9l intake is leaking-- suppose you guys can talk me into going it...? --- |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
1996 Dodge Grand Caravan LE AC/Heater Blower, Relay and Resistor Block Problems 101 | HeadlessHorseman | Dodge | 0 | January 5th 05 02:49 PM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | October 16th 04 05:28 AM |
Intrepid - Concorde comparison? | johndoe | Dodge | 10 | August 3rd 04 06:51 PM |