If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
1984 Audi 4000S Quattro brake bleeding
Hi,
I think there is air in my rear brake lines, but bleeding is a rediculous pain. I know the proportioning valve on the '84 is not adjustable, but is there a way to disable it? I know the first ones on Jeeps there was a button that could be held. I just want a way to keep normal pressure or lot's of pressure to the rears while bleeding. Right now I can bleed once and then the rears get closed off. My main problem is that I have either a leak or air in my lines, but I can't see a leak and don't seem to lose fluid. If I press my brake pedal slowly it goes about 3/4 or 7/8 to the floor, but still feels like a normal pedal. When it does this I get pressure to all 4 wheels, but probably about half of what I'd call normal pressure. If I push the pedal more rapidly or fast it will only go half way and feel like a normal pedal with full pressure, but only the front wheels will have pressure. I'm hoping it's just air in the rear lines and under lots of pressure that compressed enough to divert the flow and close off the rears. If it's something more serious then maybe there's a way I can make the fronts always have the pressure? Right now I can brake fine with the mostly depressed pedal, I'm just worried when I go to get the car inspected they will say it's inappropriate that way. Thanks for any help, Chris |
Ads |
#2
|
|||
|
|||
Chris,
The brake system is supposed to be a closed system, so any air in the lines or loss of pressure is a serious issue. On the proportioning valve, it's supposed to reduce the pressure to the rears when the car brakes - as when the nose dives - thus pulling on the spring which activates the valve. In order to bleed the system, IIRC, you have to fool the prop. valve into thinking that the car's suspension is at rest (some of the postings on Audifans mention pulling the prop valve lever to the rear of the car). If you don't trick the valve, you'll only have 20% of the brake pressure going to the rear, and 80% to the front. WRT the brake system, if you're using the original lines then you're asking for trouble. Old lines can become herneated and collapsed internally and you'd never see a problem until they burst. Check the hard lines for excessive corrosion as well - you can get lengths of metric bubble flare tubing at your local FLAPS. The difference between slow and fast presses of the pedal sounds like brake fluid is bypassing the plunger in the master cylinder. I have read postings where people have mentioned that the seals in the MC get damaged while bleeding, as they pass along areas of the cylinder that they wouldn't normally (and where some corrosion may exist) when the pedal is pumped to the floor. Brakes are something that should not be "mickey moused" - they're not optional equipment. You need all 4 wheels to have them, not the fronts only. Cheers! Steve Sears 1987 Audi 5kTQ 1980 Audi 5k 1962 and '64 Auto Union DKW Junior deLuxes (SPAM Blocker NOTE: Remove SHOES to reply) > wrote in message oups.com... > Hi, > I think there is air in my rear brake lines, but bleeding is a > rediculous pain. I know the proportioning valve on the '84 is not > adjustable, but is there a way to disable it? I know the first ones on > Jeeps there was a button that could be held. I just want a way to keep > normal pressure or lot's of pressure to the rears while bleeding. > Right now I can bleed once and then the rears get closed off. > > My main problem is that I have either a leak or air in my lines, but I > can't see a leak and don't seem to lose fluid. If I press my brake > pedal slowly it goes about 3/4 or 7/8 to the floor, but still feels > like a normal pedal. When it does this I get pressure to all 4 wheels, > but probably about half of what I'd call normal pressure. If I push > the pedal more rapidly or fast it will only go half way and feel like a > normal pedal with full pressure, but only the front wheels will have > pressure. I'm hoping it's just air in the rear lines and under lots of > pressure that compressed enough to divert the flow and close off the > rears. If it's something more serious then maybe there's a way I can > make the fronts always have the pressure? Right now I can brake fine > with the mostly depressed pedal, I'm just worried when I go to get the > car inspected they will say it's inappropriate that way. > > Thanks for any help, > Chris > |
#3
|
|||
|
|||
I wish I had a spring or a lever. This is an '84. '85 to '87 used the
spring and lever to tell suspension diving and adjust accordingly, it was an adjustable prop. valve. The '84 does not have this. My prop valve is just below the master cylinder and completely unadjustable. All of my brake lines are steel and seem to be in good order. I was looking/hoping for that fooling pressure to the rear step you mentioned but for an '84. My brakes do work as per new if I push the pedal 'slowly' or whatnot, I'm thinking when pushing fast it sense a rear leak and closes off pressure. I suppose I should have been saying combination valve the whole time instead of prop.valve. Anyway, thanks for your help, Chris Steve Sears wrote: > Chris, > The brake system is supposed to be a closed system, so any air in the lines > or loss of pressure is a serious issue. On the proportioning valve, it's > supposed to reduce the pressure to the rears when the car brakes - as when > the nose dives - thus pulling on the spring which activates the valve. In > order to bleed the system, IIRC, you have to fool the prop. valve into > thinking that the car's suspension is at rest (some of the postings on > Audifans mention pulling the prop valve lever to the rear of the car). If > you don't trick the valve, you'll only have 20% of the brake pressure going > to the rear, and 80% to the front. > WRT the brake system, if you're using the original lines then you're asking > for trouble. Old lines can become herneated and collapsed internally and > you'd never see a problem until they burst. Check the hard lines for > excessive corrosion as well - you can get lengths of metric bubble flare > tubing at your local FLAPS. The difference between slow and fast presses of > the pedal sounds like brake fluid is bypassing the plunger in the master > cylinder. I have read postings where people have mentioned that the seals > in the MC get damaged while bleeding, as they pass along areas of the > cylinder that they wouldn't normally (and where some corrosion may exist) > when the pedal is pumped to the floor. > Brakes are something that should not be "mickey moused" - they're not > optional equipment. You need all 4 wheels to have them, not the fronts > only. > Cheers! > Steve Sears > 1987 Audi 5kTQ > 1980 Audi 5k > 1962 and '64 Auto Union DKW Junior deLuxes > (SPAM Blocker NOTE: Remove SHOES to reply) > > wrote in message > oups.com... > > Hi, > > I think there is air in my rear brake lines, but bleeding is a > > rediculous pain. I know the proportioning valve on the '84 is not > > adjustable, but is there a way to disable it? I know the first ones on > > Jeeps there was a button that could be held. I just want a way to keep > > normal pressure or lot's of pressure to the rears while bleeding. > > Right now I can bleed once and then the rears get closed off. > > > > My main problem is that I have either a leak or air in my lines, but I > > can't see a leak and don't seem to lose fluid. If I press my brake > > pedal slowly it goes about 3/4 or 7/8 to the floor, but still feels > > like a normal pedal. When it does this I get pressure to all 4 wheels, > > but probably about half of what I'd call normal pressure. If I push > > the pedal more rapidly or fast it will only go half way and feel like a > > normal pedal with full pressure, but only the front wheels will have > > pressure. I'm hoping it's just air in the rear lines and under lots of > > pressure that compressed enough to divert the flow and close off the > > rears. If it's something more serious then maybe there's a way I can > > make the fronts always have the pressure? Right now I can brake fine > > with the mostly depressed pedal, I'm just worried when I go to get the > > car inspected they will say it's inappropriate that way. > > > > Thanks for any help, > > Chris > > |
#4
|
|||
|
|||
Chris,
You might try asking the 4k people on Audiworld, or try Huw at www.humanspeakers.com/audi I have cc'd the q-list at Audifans to see if someone may be able to provide assistance (q-listers, e-mail replies to Chris directly) Cheers! Steve Sears 1987 Audi 5kTQ 1980 Audi 5k 1962 and '64 Auto Union DKW Junior deLuxes (SPAM Blocker NOTE: Remove SHOES to reply) > wrote in message oups.com... > I wish I had a spring or a lever. This is an '84. '85 to '87 used the > spring and lever to tell suspension diving and adjust accordingly, it > was an adjustable prop. valve. The '84 does not have this. My prop > valve is just below the master cylinder and completely unadjustable. > All of my brake lines are steel and seem to be in good order. I was > looking/hoping for that fooling pressure to the rear step you mentioned > but for an '84. > > My brakes do work as per new if I push the pedal 'slowly' or whatnot, > I'm thinking when pushing fast it sense a rear leak and closes off > pressure. I suppose I should have been saying combination valve the > whole time instead of prop.valve. > > Anyway, thanks for your help, > Chris > > Steve Sears wrote: > > Chris, > > The brake system is supposed to be a closed system, so any air in the lines > > or loss of pressure is a serious issue. On the proportioning valve, it's > > supposed to reduce the pressure to the rears when the car brakes - as when > > the nose dives - thus pulling on the spring which activates the valve. In > > order to bleed the system, IIRC, you have to fool the prop. valve into > > thinking that the car's suspension is at rest (some of the postings on > > Audifans mention pulling the prop valve lever to the rear of the car). If > > you don't trick the valve, you'll only have 20% of the brake pressure going > > to the rear, and 80% to the front. > > WRT the brake system, if you're using the original lines then you're asking > > for trouble. Old lines can become herneated and collapsed internally and > > you'd never see a problem until they burst. Check the hard lines for > > excessive corrosion as well - you can get lengths of metric bubble flare > > tubing at your local FLAPS. The difference between slow and fast presses of > > the pedal sounds like brake fluid is bypassing the plunger in the master > > cylinder. I have read postings where people have mentioned that the seals > > in the MC get damaged while bleeding, as they pass along areas of the > > cylinder that they wouldn't normally (and where some corrosion may exist) > > when the pedal is pumped to the floor. > > Brakes are something that should not be "mickey moused" - they're not > > optional equipment. You need all 4 wheels to have them, not the fronts > > only. > > Cheers! > > Steve Sears > > 1987 Audi 5kTQ > > 1980 Audi 5k > > 1962 and '64 Auto Union DKW Junior deLuxes > > (SPAM Blocker NOTE: Remove SHOES to reply) > > > wrote in message > > oups.com... > > > Hi, > > > I think there is air in my rear brake lines, but bleeding is a > > > rediculous pain. I know the proportioning valve on the '84 is not > > > adjustable, but is there a way to disable it? I know the first ones on > > > Jeeps there was a button that could be held. I just want a way to keep > > > normal pressure or lot's of pressure to the rears while bleeding. > > > Right now I can bleed once and then the rears get closed off. > > > > > > My main problem is that I have either a leak or air in my lines, but I > > > can't see a leak and don't seem to lose fluid. If I press my brake > > > pedal slowly it goes about 3/4 or 7/8 to the floor, but still feels > > > like a normal pedal. When it does this I get pressure to all 4 wheels, > > > but probably about half of what I'd call normal pressure. If I push > > > the pedal more rapidly or fast it will only go half way and feel like a > > > normal pedal with full pressure, but only the front wheels will have > > > pressure. I'm hoping it's just air in the rear lines and under lots of > > > pressure that compressed enough to divert the flow and close off the > > > rears. If it's something more serious then maybe there's a way I can > > > make the fronts always have the pressure? Right now I can brake fine > > > with the mostly depressed pedal, I'm just worried when I go to get the > > > car inspected they will say it's inappropriate that way. > > > > > > Thanks for any help, > > > Chris > > > > |
#5
|
|||
|
|||
1984 Audi 4000S Quattro brake bleeding
Do audi's require a different brake bleeding procedure after you replace the master cylinder, I have a 1993 quattro 100cs and I'm having problems. Any suggestions? -- kevind1 ------------------------------------------------------------------------ kevind1's Profile: http://www.audiforum.ca/member.php?userid=7420 View this thread: http://www.audiforum.ca/showthread.php?t=6543 |
#6
|
|||
|
|||
1984 Audi 4000S Quattro brake bleeding
abs equipped?
Are you using a pressure bleeder? Or the old foot method? What problems are you having? If you are using the foot/ pressure bleeder method I recommend that you bleed the master first by slightly opening 1 brake line at a time on the master, pump if needed until you get a solid stream of fluid out, close off that line. Do that with all of them and then bleed at the 4 corners furthest away from the master. There might be a valve that you have to hold open at the rear axle, but I am not sure of your model having this. "kevind1" > wrote in message ... > > Do audi's require a different brake bleeding procedure after you replace > the master cylinder, I have a 1993 quattro 100cs and I'm having > problems. Any suggestions? |
#7
|
|||
|
|||
1984 Audi 4000S Quattro brake bleeding
Thanks for the new information. I'll use that trick you said about bleeding at the master cylinder. I've never tried that before and that should help. Thanks -- kevind1 ------------------------------------------------------------------------ kevind1's Profile: http://www.audiforum.ca/member.php?userid=7420 View this thread: http://www.audiforum.ca/showthread.php?t=6543 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Brake Bleeding Problem - '82 Rabbitt Diesel | Wray McDonnell | VW water cooled | 2 | March 31st 05 06:35 PM |
Brake rotors already grooving | [email protected] | Technology | 46 | January 15th 05 03:42 PM |
brake pads for 2001 Audi A4 2.8L V6 Quattro | Curtis Newton | Audi | 2 | November 18th 04 02:44 PM |
'84 Audi 4000s Quattro brake issues, balancing | ItJstAGame | Audi | 2 | July 23rd 04 04:17 AM |
2001 Audi TT Quattro FOR SALE | Gary | Audi | 0 | June 14th 04 03:46 PM |