If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Chevy pickup - bad starter or faulty wiring?
I have an old 87 Chevy truck V8 that won't start. Had been starting
and running fine til a few days ago. But a little background history first.. The truck always starts up fine the first time. But if it's been driven for awhile, then shut off - such as stopping for gas - then try to restart, it's a little more difficult to start. But usually I get it started ok. Recently, with the extreme hot weather in our area it's been particularly difficult to start. After doing some research on this, thought it might just be vapor lock. The key here, though, is that is runs great after started - doesn't die on me, etc. The other day I drove to work just fine. But at the end of my work day when I went out to start her up, she would only crank slowly but wouldn't start. When this has happened before I would usually wait awhile and sometime up to a day later then she would start up fine. But now even after waiting several days she simply won't start up anymore. Engine cranks slowly and after a few more tries, just clicks. So I bought a new battery and after hooking it up the starter doesn't even click. The lights, radio and wipers work ok but nothing else happens after turning the ignition. A discovery I made while unhooking my old battery was that the rubber boot covering the positive cable connector was somewhat melted as if exposed to extreme heat. So maybe the cable running from my battery's positive post to the starter's terminal is bad? Now, my immediate problem...my truck is stuck at the parking lot at work. The gate is locked up after evening so I don't have access to work on it after I've gotten off work. I'd really like to get her home to work on but am reluctant to pay any towing charges at this point. I don't see the logic in incurring erroneous expense on such an old truck if there's an easier, and more importantly, cheaper way to accomplish the same task. I've read instructions previously on this forum outlining the way to jump-start (hotwire) a starter when diagnosing a no-start scenario. What I want to do is start my truck up and drive it home so I can work on it. But I'm not clear on some of the instructions I've read here about the proper way to do this. What are the proper connections between the battery and the starter to get the engine started so that it continues running? Should the ignition key be in the on position? I've read elsewhere that it doesn't need to be. Assuming that my battery cable to the starter is bad, my only option appears to be to run a jumper cable from the positive post of my battery to the solenoid. But since there are several terminals on the solenoid, which terminal do I connect to? Should I leave it connected after the engine starts? Will the engine continue to run if I remove the connection? I've read so many conflicting instructions on the web detailing this that I'm simply not clear on the proper way to do this. I just feel that if I can get my truck home I can get her fixed without incurring too much expense on my part. Any and all input would sure be appreciated - thanks in advance! major |
Ads |
#2
|
|||
|
|||
Chevy pickup - bad starter or faulty wiring?
|
#3
|
|||
|
|||
Chevy pickup - bad starter or faulty wiring?
> > > Get a few buddies to help you push it outside the gate at lunch > time........ > > Can't do that, my truck would then be sitting in the middle of a major intersection. Anybody out there with an informed reponse to my inquiry about hot-wiring the starter? Thanks. |
#4
|
|||
|
|||
Chevy pickup - bad starter or faulty wiring?
> I've read instructions previously on this forum outlining the way to
> jump-start (hotwire) a starter when diagnosing a no-start scenario. > What I want to do is start my truck up and drive it home so I can work > on it. But I'm not clear on some of the instructions I've read here First off, the ignition switch needs to be in the on position. You need to jump between the large copper lug and the smaller "start" terminal to make the starter run. But before you jump under the truck to do this understand that by completing the circuit there is a risk of welding the terminal to together whatever tool(screwdriver, etc) you use to bridge the connection. Before you get too far into this check for +12 volts at the battery connection at the starter. If you do not have 12 volts here then you either need to repair/replace the battery cable or call the tow truck. One way to temp-fix the problem if the wiring from the ign switch to the starter is bad is to run a jumper wire from the positive terminal of the battery to the smaller "start" terminal on the starter. The start terminal is the one that gets the 12 volt signal from the ignition switch to engage the starter. This method carries a smaller risk of welding things together. If that does not work then you can try jumping between the large connection at the starter and the smaller start terminal, but if the starter is totally shot or if the larger 12 volt cable from the battery has a burned out fusible link this also will fail. It's times like this when you wish you had a manual transmission so you could push start it and get it home Chris |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Power Window Sticking - 96 Chevy Pickup | bob | Technology | 7 | March 2nd 05 04:05 AM |
WTB: Transmission - 5-speed 2x4 for 1988 or 1989 Chevy C1500 pickup | Gene | Technology | 1 | March 1st 05 06:18 AM |
Was: 96 Chevy Pickup Intake Leak? | bob | Technology | 1 | December 15th 04 12:13 AM |
96 Chevy Pickup Intake Leak? | bob | Technology | 2 | December 13th 04 01:57 PM |
Does this sound like a bad starter? | Dave K. | General | 14 | April 8th 04 07:38 PM |