If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
Low-speed suspension noises? (300m)
"Percival P. Cassidy" wrote:
> 2002 300M with Performance Handling Package. 135K miles. > > Not-so-loud low-pitched "clunking" noise on uneven surfaces at > low speed I can't believe that (a) you've never read or remembered any of my previous posts regarding suspension on my '00 300m, and (b) that nobody else here has posted the obvious cause of your clunking: -> Front Sway Bar Bushings. Anyone with an LH-body car knows that you'll need to replace those as often as you replace your front disk brake pads. I've done mine 3 times. Also, unless you've verified the state of rust of your front struts, lower spring retaining plate, be aware that they will rust and fail and cause the spring to bottom out on the steering link arm, possibly causing the retaining plate to come into contact with your tire. Definately something you don't want to happen during high-speed driving. It happened to me 2 years ago as I hit a pothole at the bottom of a long dip in the road, but I was only going maybe 25 mph and had just a fraction of an inch clearance to the tire - and was able to drive home and (later the next day) replace the strut (monroe quick-strut, which I think was never right since day one in terms of clunking and will probably change it again this fall). A year later I replaced the other front strut - the lower spring retaining plate was half rusted and could have failed at any time. I have since replaced these: - front sway bar links - lower control arm (driver's side) - front tension rod + bushings (driver's side) - and like I said, front sway bar bushings (several times) - have also replaced rear sway bar bushings (once) I've not yet changed the outer tie-rod ends (that's not a job I'd look forward to unless I know for sure they are worn and causing knocking). But like I've already said, the first place to look for the cause of a knock in the front while driving over slightly uneven pavement at city driving speed is the front sway bar bushings. |
Ads |
#12
|
|||
|
|||
Low-speed suspension noises? (300m)
On 09/06/14 11:37 am, MoPar Man wrote:
> "Percival P. Cassidy" wrote: > >> 2002 300M with Performance Handling Package. 135K miles. >> >> Not-so-loud low-pitched "clunking" noise on uneven surfaces at >> low speed > > I can't believe that (a) you've never read or remembered any of my > previous posts regarding suspension on my '00 300m, and (b) that nobody > else here has posted the obvious cause of your clunking: > > -> Front Sway Bar Bushings. > > Anyone with an LH-body car knows that you'll need to replace those as > often as you replace your front disk brake pads. > > I've done mine 3 times. > > Also, unless you've verified the state of rust of your front struts, > lower spring retaining plate, be aware that they will rust and fail and > cause the spring to bottom out on the steering link arm, possibly > causing the retaining plate to come into contact with your tire. > Definately something you don't want to happen during high-speed driving. > > It happened to me 2 years ago as I hit a pothole at the bottom of a long > dip in the road, but I was only going maybe 25 mph and had just a > fraction of an inch clearance to the tire - and was able to drive home > and (later the next day) replace the strut (monroe quick-strut, which I > think was never right since day one in terms of clunking and will > probably change it again this fall). > > A year later I replaced the other front strut - the lower spring > retaining plate was half rusted and could have failed at any time. > > I have since replaced these: > > - front sway bar links > - lower control arm (driver's side) > - front tension rod + bushings (driver's side) > - and like I said, front sway bar bushings (several times) > - have also replaced rear sway bar bushings (once) > > I've not yet changed the outer tie-rod ends (that's not a job I'd look > forward to unless I know for sure they are worn and causing knocking). > > But like I've already said, the first place to look for the cause of a > knock in the front while driving over slightly uneven pavement at city > driving speed is the front sway bar bushings. Sorry, but I don't recall reading your posts about replacing sway-bar bushings. In the meantime, however, I had bought new sway-bar bushings anyway (as being easier to replace, perhaps, than the inner tie-rod-end bushings, and because I could not detect play in the steering), but I haven't yet installed them. I did look at the struts when I was under the car changing the oil a couple of days ago, and although the rubber pads at the bottom of the springs were a mess, the struts themselves didn't seem to be in bad shape. What struts did you buy? There don't seem to be any aftermarket ones that are compatible with the Performance Handling Package, and I see recommendations to use the genuine MoPar ones. How many miles on your '00 300M? Perce |
#13
|
|||
|
|||
Low-speed suspension noises? (300m)
"Percival P. Cassidy" wrote:
> > I can't believe that (a) you've never read or remembered any of > > my previous posts regarding suspension on my '00 300m > > Sorry, but I don't recall reading your posts about replacing sway- > bar bushings. See below. > In the meantime, however, I had bought new sway-bar bushings > anyway (as being easier to replace, perhaps, than the inner > tie-rod-end bushings, and because I could not detect play in > the steering), but I haven't yet installed them. Apparently, 300m with PHP had a front sway bar that was 1" in diameter, while regular 300m the swaybar was something like 1/16" smaller. Hence when you look up the part, you'll be asked if you had php. Personally, I'd get the smaller bushing. It will take longer to develop play because of a tighter fit. Will probably be half the price. > I did look at the struts when I was under the car changing the oil > a couple of days ago, and although the rubber pads at the bottom of > the springs were a mess, the struts themselves didn't seem to be in > bad shape. Have a look at this: http://www.crankshift.com/wp-content...rson-strut.jpg See the round lower plate that is holding up the spring? Either from the top or the bottom, look at how that plate is welded to the strut tube. It's very common for that weld or the part of the plate around the weld to break down due to rust. > What struts did you buy? Monroe quick struts. They come fully assembled with spring. > There don't seem to be any aftermarket ones that are compatible > with the Performance Handling Package, and I see recommendations > to use the genuine MoPar ones. A year or two ago I was reading a lot about this on a couple of the chrysler / 300m web forums. I wasn't focusing on any differences between regular and php, but honestly I think you'd be fine using the regular struts. I *believe* there were discussions on those boards about using the regular aftermarket struts on the php, but I don't remember if there was a consensus that yes, the regular struts are ok (from a size / fit pov). What I do remember is that about a year or two prior to me buying my first monroe quickstrut, there were many documented cases of these struts either not being designed right or not being assembled correctly at the factory. So a lot of people were down on them because of that. I think there is something that is not quite right with the first one I bought back in Dec. 2012. Example: ----------- After a lot of wasted time I finally found a couple posts for other cars that had similar problems that came from Monroe not properly tightening the top strut nut to anywhere close to 60ft/lbs. After fighting my way to gain acess to the top nut I found that it must have just been put on finger tight. http://www.amazon.ca/Monroe-171957-Q.../dp/B000C55L0M ----------- > How many miles on your '00 300M? As of right now - 120k miles. =============== Subject: '02 300M: When to replace struts? Date: Sat, 11 May 2013 22:12:53 -0400 From: MoPar Man > Newsgroups: rec.autos.makers.chrysler "Percival P. Cassidy" wrote: > 126K miles now. Is there any particular mileage at which it would > be advisable to replace the struts? I'm not aware of any > significant problems, but any deterioration would have been very > gradual and probably not noticeable. Any way of testing? I have replaced the two front struts and one rear strut on my '00 300m. It has about 112k miles on it. The rear strut was replaced because back in Dec. 2011 or Jan 2012 (I forget exactly when) I hadn't yet put my snow tires on the back wheels, and going down a slight hill with a slight bend I spun around and the rear tire hit the curb flat-on and bent the rim (chrome Razor-Star factory original) and bent the rear spindle down about 5 degrees. The outer surface of the rim was deeply cracked for a few inches, but the rim and tire remained air-tight. After the impact, that wheel continued to turn true (no wobble) but the wheel/tire was riding on an angle relative to true verticle (by about an inch at the top of the tire). I continued to drive the car like that for almost a year (only short-distance, inner city driving - nothing faster than 50 mph) until I fixed it. It turns out that the bearing race had cracked, but the cracked piece stayed put. I bought a new bearing, knuckle (with axle), and quick strut. But I suspect that there was something wrong with that strut before the impact. To answer your question more directly... One of my front struts failed some-what catastrophically this past Dec 24 - the day before a 100 mile highway drive to visit relatives. The lower plate that the spring rides on had become detached from the strut-tube due to rust, and the spring forced the plate into contact with the steering arm and torsion-link arm located about 1 inch down the tube. Those arms are very strong and prevented the plate from contacting the tire (just barely). I bought a Monroe quick-strut that day, and by 10 pm Dec 24 I had the new strut mounted and ready for the drive the next morning. About 2 months ago I replaced the other front strut because I noticed that about half of the weld holding the lower plate to the strut tube was basically gone - again due to rust. So here's a picture of what a new strut looks like: http://i.ebayimg.com/00/s/MTIwMFgxMjAw/z/yQ4AAOxyA4ZRPkAh/$T2eC16hHJIQE9qUHu0VFBRPk!gzQLQ~~60_12.JPG?set_id= 880000500F The lower spring-seat is the round plate under the spring. It is welded to the strut tube. That weld is what will rust away. It will be easier to see that weld if you jack up the front of the car and slide the corrogated protector tube up to get a clear view of the weld. My 300m has some surface rust along the bottom edge of some of the doors, but otherwise I wouldn't have thought that there could be any place on or under the car that would be suffering rust dammage to that extent that I saw on those struts. I've already replaced the front sway-bar links once a few years ago, and the front sway bar bushings. During all this work I replaced the front sway-bar bushings a second time - and found the new set to be too loose so I had to modify them to fit better. I also replaced the rear sway bar bushings. Since I still have a noticable knock in the front end, I'm going to replace the lower control arms next, and the front tension-bar to frame bushings while I'm at it. At some point this year I'm also going to replace the front wheel bearings, but those axle nuts are going to be a bitch to take off... |
#14
|
|||
|
|||
Low-speed suspension noises? (300m)
On 09/07/14 12:11 am, MoPar Man wrote:
>>> I can't believe that (a) you've never read or remembered any of >>> my previous posts regarding suspension on my '00 300m >> >> Sorry, but I don't recall reading your posts about replacing sway- >> bar bushings. > > See below. > >> In the meantime, however, I had bought new sway-bar bushings >> anyway (as being easier to replace, perhaps, than the inner >> tie-rod-end bushings, and because I could not detect play in >> the steering), but I haven't yet installed them. > > Apparently, 300m with PHP had a front sway bar that was 1" in diameter, > while regular 300m the swaybar was something like 1/16" smaller. Hence > when you look up the part, you'll be asked if you had php. > > Personally, I'd get the smaller bushing. It will take longer to develop > play because of a tighter fit. Will probably be half the price. Non-PHP sway bar is 1", PHP sway bar is 1 1/16". Both bushings are same price at NAPA (and everywhere else, IIRC). I bought the PHP ones. Perce |
#15
|
|||
|
|||
Low-speed suspension noises? (300m)
"Percival P. Cassidy" wrote:
> > Personally, I'd get the smaller bushing. It will take longer to > > develop play because of a tighter fit. Will probably be half the > > price. > > Non-PHP sway bar is 1", PHP sway bar is 1 1/16". Both bushings are > same price at NAPA (and everywhere else, IIRC). I bought the PHP > ones. So what I've done regarding the front sway bar bushing - I get more life out of them by doing this: When you look at them from the side, they look like a big, fat letter C, with almost no gap on the righthand side. I cut the gap bigger using a band saw, then I take a piece of hard pastic that's about 1/16" thick and cut it so it matches the size of the bottom of the bushing (about 2" x 3"). I use that as a spacer and place it under the bushing when I re-install it. The extra height caused by the plastic spacer means that as you tighten down on the metal bushing retainer, the retainer will squeeze the bushing down a little more than it ordinarily would, and the wider gap that I cut into the bushing allows it to close down tighter against the sway bar. |
#16
|
|||
|
|||
Sway-bar bushings. Was: Low-speed suspension noises?
On 08/13/14 07:48 pm, Percival P. Cassidy wrote:
> 2002 300M with Performance Handling Package. 135K miles. > > Not-so-loud low-pitched "clunking" noise on uneven surfaces at low speed > -- e.g., when coasting (not necessarily braking) as I approach a red > light or stop sign. > > Can't say that I've noticed the noise at higher speeds. > > No suspension or steering parts have ever been replaced. > > Where do I start looking? What might it cost me to fix? What special > tools would I need to tackle the job myself? I have the inner tie-rod-end bushing kit, but I decided to start with the sway bar bushings. The bolts for the driver's side came out fairly easily, and once they were out the sway bar moved freely and I was able to remove the old bushing (seem,s worn more one side than the other) and fit the new one. I don't know how to judge the torque accurately, as there's no room to get my torque wrench in there -- was I supposed to remove the wheel? Or maybe I can get the torque wrench in there when the car is down off the ramps and I can turn the wheel to the left. The first (rear) bolt on the passenger side came out fairly easily, but the front bolt was a real pain to remove -- felt like 60 ft. lbs. to get it to move just about all the way even with liberal applications of Screw Loose, When I did get it out, I found that the bottom part of the bolt had additional metal caught up in the threads, so now in what condition are the threads into which it screws? Will merely replacing the bolt solve the problems? Unlike the driver's side, the passenger's side end of the sway bar does not want to move, and the old bushing is pinched tight against the frame. Jack up that corner and take the load off the suspension that side? Perce |
#17
|
|||
|
|||
Sway-bar bushings. Was: Low-speed suspension noises?
"Percival P. Cassidy" > writes:
> > Unlike the driver's side, the passenger's side end of the sway bar > does not want to move, and the old bushing is pinched tight against > the frame. Jack up that corner and take the load off the suspension > that side? You should have put the front up on jack stands before you started. |
#18
|
|||
|
|||
Sway-bar bushings. Was: Low-speed suspension noises?
On 09/08/14 08:24 pm, Joe Pfeiffer wrote:
>> Unlike the driver's side, the passenger's side end of the sway bar >> does not want to move, and the old bushing is pinched tight against >> the frame. Jack up that corner and take the load off the suspension >> that side? > > You should have put the front up on jack stands before you started. I have jack stands, but they are the wrong shape to fit the jacking points on the car. And where would I place the jack so the jack stands can support the car in the right place? Why did one end of the sway bar move freely and the other not? Anyway, I got the old bushing out and installed the new one, but the bolt that brought other metal out with it -- after cleaning up the threads of both the bolt and the part into which it screws -- does not grip. I'm thinking of trying to find a longer bolt with the same thread and putting a nylock nut on the bottom. Perce |
#19
|
|||
|
|||
Sway-bar bushings. Was: Low-speed suspension noises?
"Percival P. Cassidy" > writes:
> On 09/08/14 08:24 pm, Joe Pfeiffer wrote: > >>> Unlike the driver's side, the passenger's side end of the sway bar >>> does not want to move, and the old bushing is pinched tight against >>> the frame. Jack up that corner and take the load off the suspension >>> that side? >> >> You should have put the front up on jack stands before you started. > > I have jack stands, but they are the wrong shape to fit the jacking > points on the car. And where would I place the jack so the jack stands > can support the car in the right place? I made some pads to put on my jack stands so I could use them under my Intrepid. > Why did one end of the sway bar move freely and the other not? Good question -- though the way I'd phrase it would be "why did one side work?" That the other didn't is no surprise at all. > Anyway, I got the old bushing out and installed the new one, but the > bolt that brought other metal out with it -- after cleaning up the > threads of both the bolt and the part into which it screws -- does not > grip. I'm thinking of trying to find a longer bolt with the same > thread and putting a nylock nut on the bottom. > > Perce |
#20
|
|||
|
|||
Sway-bar bushings. Was: Low-speed suspension noises?
"Percival P. Cassidy" wrote:
> I don't know how to judge the torque accurately, I have a torque wrench - but the only time (recently) that I've used it was to replace the front wheel bearing nut. I figured it was important to set the torque of that nut to factory specs. Other than that, I use a liberal amount of torque, as judged by hand, on any bolt I reinstall. So in other words - no need to get all bent out of shape trying to torque each and every bolt according to the book. > When I did get it out, I found that the bottom part of the > bolt had additional metal caught up in the threads, so now > in what condition are the threads into which it screws? > Will merely replacing the bolt solve the problems? Looks like (based on your next post) that bolt was stripped at the factory. I'd just try to install a bolt with SAE thread (english thread - not metric). Would probably work at least once. Next time you'll probably have to tap new threads. > Unlike the driver's side, the passenger's side end of the sway > bar does not want to move, and the old bushing is pinched tight > against the frame. Jack up that corner and take the load off > the suspension that side? I use a small bottle jack to lift the sway bar if I need to reposition it. I've used a bottle jack to pop the outer tierod end out of it's hole when I was replacing one of the front struts. I've also used a bottle jack placed at the end of my ratchet (or wrench) to turn some stubborn bolts. It's a little tricky and unstable, but it works when you need it. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Front suspension squeaks over speed bumps | Dan[_6_] | Technology | 4 | December 20th 09 07:41 AM |
Is it Ok to Use Hard Suspension Pads on a 2004 with standard suspension? | Sheldon Rudie | Mazda | 4 | January 17th 08 12:31 AM |
two fan noises 92 e32 | Damen Garr | BMW | 0 | November 8th 05 04:30 AM |
e34 noises... | mojo7676 | BMW | 1 | December 28th 04 07:33 PM |
Strange noises | Ashley | Audi | 2 | May 27th 04 01:40 AM |