If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Weber linkage help
I am helping to salvage a junkyard find -- 1972 Bay bus with a type 4
engine. Previous owner has installed a single, center mounted, Weber 2bbl mainfold and carb. Carb is oriented with linkage on drivers side of vehicle. Stock accelerator cable passes through engine tin approx 10" to drivers side of vehicle centerline. Existing carb linkage rotates clockwise and actuator must be pulled straight down. ( Linkage arm can be rotated 180 deg to move straight UP.) Accelerator does not work since it pulls parallel to the floor of the bus -- 90 deg from linkage required motion. Now the questions: 1) Is the carb oriented properly or does it need to rotate 180 deg ? 2) CIP lists part #C13-43-0602 - UNIVERSAL LINKAGE KIT FOR ALL WEBER 2BBL PROGRESSIVE CARBURETORS. Will this solve my problem? 3) Has anyone used this setup before? What do I need to make it work? Thanks, -- Chris Corfias 71 SB convert 78 bay bus |
Ads |
#2
|
|||
|
|||
"tim horvath" > wrote:
>3) Has anyone used this setup before? What do I need to make it work? Regarding the linkage geometry, I can't be much assistance to you. But I can say this.. I had a progressive 32/36 DFEV in my beetle with the redline "premium" heated manifold. Suffice to say, it had an awful off idle bog, and no matter how much idle jet or accel pump changes I did, the bog was always present. Even with an SVDA distributor, the bog was always there. Should I have used a different cam? Possibly.. I never solved it. On the T4, I'm sure the runner lengths are shorter, and that might have been the main problem with a T1 setup. Good luck getting your Weber to behave even after you solve the linkage issue. Sorry for the tone of this. I just couldn't get the carb to behave. The carb did add more giddy-up once you were off the bog. Go with dual 40IDFs with the enrichment circuit, or any other pair of carbs on _short_ runners for a better setup, IMHO. -- David Gravereaux > [species: human; planet: earth,milkyway(western spiral arm),alpha sector] |
#3
|
|||
|
|||
The carb is mounted 180 degrees wrong(unless you have aRHD Bus).The linkage
should be on the right side,the cable will have to pass thru a tube in the firewall tin to work smoothly and it will be a bear to adjust.It does the job,but be prepared for an off idle bog(made worse by the 009 distributor that seems to always keep company with this bad boy).Also, cables for this application are an area to be explored.I only say this because "Hans",my formerly trusted Westy,sits mocking me in the garage so equipped.Enjoy,Steve "tim horvath" > wrote in message ... >I am helping to salvage a junkyard find -- 1972 Bay bus with a type 4 > engine. Previous owner has installed a single, center mounted, Weber 2bbl > mainfold and carb. Carb is oriented with linkage on drivers side of > vehicle. Stock accelerator cable passes through engine tin approx 10" to > drivers side of vehicle centerline. Existing carb linkage rotates > clockwise > and actuator must be pulled straight down. ( Linkage arm can be rotated > 180 > deg to move straight UP.) > > Accelerator does not work since it pulls parallel to the floor of the > bus -- > 90 deg from linkage required motion. > > Now the questions: > > 1) Is the carb oriented properly or does it need to rotate 180 deg ? > 2) CIP lists part #C13-43-0602 - UNIVERSAL LINKAGE KIT FOR ALL WEBER > 2BBL > PROGRESSIVE CARBURETORS. Will this solve my problem? > 3) Has anyone used this setup before? What do I need to make it work? > > Thanks, > -- > Chris Corfias > > 71 SB convert > 78 bay bus > > > > > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
wiper linkage | Wwj2110 | Saturn | 1 | January 17th 05 11:45 PM |
Weber Carb | Phill | BMW | 0 | November 26th 04 12:37 PM |
Need Intake Maniford for Weber Carbs (1984 Spider Volace) | r.amber | Alfa Romeo | 0 | June 19th 04 10:28 PM |
Steering linkage prob | Richard Cox | 4x4 | 8 | March 4th 04 06:31 PM |