If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Dead transmission? No power to wheels
I just did a motor/tranny swap on my 96 Prelude: I installed a JDM H22,
and the original 5-speed tranny that was paired with that engine. After installing the axles, I noticed that they spun freely, even when the tranny was in gear. After bleeding the clutch, I started the engine, put it in gear, and let out the cluch. I could hear the "normal" noise when the clutch is released in neutral, but nothing else happened. No drop on the tach, no power to the wheels at all. With the front end jacked, the wheels turn freely when the transmission is in gear. The shift selector feels perfect, but the tranny acts like it's always in neutral. Could it be that the axle isn't in the tranny all the way? Or does this sound like an internal tranny problem? Is there something I can do to further isolate the problem? I spun the wheels and watched from the bottom of the car, and both axles turn all the way to where they attach to the tranny, and there's no tranny oil leaking from where they attach. Thanks in advance for any replies! |
Ads |
#2
|
|||
|
|||
Dead transmission? No power to wheels
|
#3
|
|||
|
|||
Dead transmission? No power to wheels
Matt,
Thanks for the reply. I guess I should have specified-- what I did was replace the motor/tranny as an assembly with a JDM motor/tranny assembly. Never separated the motor/tranny that I removed, nor the one I installed. I thought about replacing the clutch on the new tranny, but I was told that the motor/tranny combo only had 30-40k miles, so I figured it ought to be good for lots of miles to come.... > Did you remember to transfer the clutch assembly (disc and pressure > plate) to the new engine? They're bolted to the flywheel and the new > engine likely wouldn't have included them. |
#4
|
|||
|
|||
Dead transmission? No power to wheels
|
#5
|
|||
|
|||
Dead transmission? No power to wheels
|
#6
|
|||
|
|||
Dead transmission? No power to wheels
> Hmmmmm. Better peel back the rubber boot and look inside the clutch
> housing to see if there's a clutch in there. Wouldn't that be a kick in > the head?? > > 'Curly' Today I got it to work, sorta... With the front end jacked, engine running and in gear, clutch pedal out, the wheels turn now, but I'm able to apply the brakes and stop them without the motor stalling. Guess this would mean a totally worn clutch pressure plate? Would it be safe to go ahead and order a new clutch set? It couldn't just be that the clutch pedal/hydrolics need further bleeding, right? I mean, if that was the case, I'd have trouble DISengaging, right? Thanks for your patience, everyone! -Randy |
#7
|
|||
|
|||
Dead transmission? No power to wheels
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
rec.autos.makers.chrysler FAQ, Part 4/6 | Dr. David Zatz | Chrysler | 0 | February 4th 06 05:25 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 5 | July 10th 05 05:24 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 5 | June 24th 05 05:27 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 5 | June 8th 05 05:28 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | November 16th 04 05:28 AM |