Looking for some database of the codes with a series of mesages or data on what the eventual fix was. Rather than just a list of codes and their meaning. A book would also be great. I have a lexus and land rover and am not interested in the USA-only readers and data. Thanks! Dean

I went to a Chain auto centre with a flat tyre.They suggested changing both front tires.I did so on the same day at same centre.@ weeks later I started hearing squealing sound when braking.I went back to same tire centre.They said my front break need to be replaced. My question should they...

I have a 1994 Dodge Ram 1500 V8 gas with a 5.2 litre. I have been having troubles with the transmission. It is wet all over the bottom of the transmission and i can not find out where it is leaking from. It also slips and has a bad acceleration when the transmission fluid and filter get some...

This is the 2.2 OHV with an electric fan. We have changed coolant and thermostat, and electric fan operates after idling for a period of time Temp is fine summer or winter driving around town, comes up to temp quick and stays there. Now that it's freezing cold outside, on the interstate in...

I replace my PCV valve once a year whether it needs it or not. The last changeout was around 6 months ago. Today I pulled the PCV valve out of the hole that it plugs into in the valve cover and the engine did not rev up like usual when the PCV valve is pulled out. I put my finger over the hole on...

1987 Lincoln Town Car. Last year my rear window de-fogger (wires in glass) worked fine. This year only the bottom half works. What can I do to fix it? I don't want to put in a new rear window just for that. The rear window was already replaced once just to get defogger to work.

hi , i have a 1988 holden jackaroo 4wd with auto trans . when i put it into drive , it is taking of in another gear 2 nd , i think. but when i put it into 1st , it takes of in 1st , but when its any other gear (reverse is fine ) its sorta struggling to take of. trans fluid is fine . i tried...

Hi all, This story might be a little involved, but basically it comes down to me having spongy brakes. I just had the front brake pads & rotors replaced, and since then, I've had to apply more force than I'm used to to get the same response from my brakes. I called the mechanic and said I...

Hello, I just changed my Ignition Coil #5 and the car ran great for a few hours and now I hit the breaks and the electrical went nuts and all gages went nuts and now when the car shuts off it wont start again and I get nothing but clicking, When I jump the car all the lights seem to work for a few...

I have a 1995 Jeep Wrangler with a 2.5 liter 4 cyl. auto. Begining several months ago, I had problems starting it. The problem in the begining almost seemed climate related. The Jeep would not start in the AM. As the afternoon came around the jeep would always start. It didn't take long to...

I made a mistake and I drove my 2007 Toyota Corolla LE with parking brake applied for approx 3-4 miles. ( with speed of 45 max) I didnt feel anything other than the hold back, but when i was about to park i could feel a smell around the car. I am not sure, if i have done some damage? thanks,...

Hi, Yesterday I went to Autozone to read codes, and I've got ''the PCM has determined that multiple random misfires have occured in cylinder #2, #3, #4 and Troubleshooting PO300, PO302, PO303, PO304.'' What does that mean? How expensive is to repair them? Just recently I've replaced the 02sensor,...

Just wondering how difficult it is to remove and install the passenger seat in a Smart car... If done right, it could be very handy to be able to snap it in and out given the limited space in one of these cars.

This engine was running flawlessly. On a fairly long highway trip, it started to misfire. By the end of the trip I am pretty sure that there were two or more cylinders misfiring. Please note that I had never experienced *any* misfires before this event. I want to make this clear because I think...

So, I've been doing some research, and I want to run a line-lock test on my car to check for a bad master cylinder. I understand what to do, but I have a simple, yet possibly stupid question: After you clamp off the lines, do you turn the car on before stepping on the brakes? Or do you do the test...

::We just rebuilt an 89 suburban 700r4 transmission and it will only engage in 1st .It barely moves in reverse. 2nd, 3rd, and 4th gear just spin. We've checked the fluids and TV cable, they seem fine.Can anyone tell me why and what we can do to fix this? Thanks in advance!:::::: :::: :::::: ...

Hello, I have a 1996 4cyc Somonna, the problem that I am having is that when the truck is rolling at speeds around 40km/h while in neutral or when the truck is in gear with the clutch pushed in, the oil pressure drops and then the truck stalls. When driving and while stopped and idling everything...

I was wondering if anyone could tell me which additional parameters I will be able to scan for once I update to the GM Enhanced OBD2 on my AutoXray? Does this increase the live data amd freeze frame parameters or does it just scan for additonal sensor inputs referenced for the CEL? According...

I'm driving a 94 Nissan Sentra LE, with 136k miles on it. On my home from work, I drive up a pretty large hill that goes for about .5 mile. During the middle of the climb I noticed my lights were flickering. This includes the headlights and the lights on the dash and radio. Does this sound like an...

I have an 85 golf that was converted from fuel injection to a carburetor. On the intake manifold, there are two hookups on the right side (the hoses have been removed) and they route 'something' under the manifold (it doesn't enter the intake area, but it's part of the actual metal). It goes in a U...